Kenwood NX-200 Service Manual

Also see for NEXEDGE NX-200: Brochure Instruction manual Instruction manual Specifications Instruction manual

NX-200(G)57ADJUSTMENTItemCondition Measurement Adjustment Specifications /RemarksPanel tuning mode PC test mode Test-equipment Unit Terminal Unit Parts Method3. Sensitivity 2adjust1) Adj item: [SENS2]Adjust: [٭٭٭]2) Adj item:[L SENS2]→[L’ SENS2]→[C SENS2]→[H’ SENS2]→[H SENS2]Adjust: [٭٭٭]Press [ ] key to storethe adjustment value.1) Adj item:[Sensitivity 2]2) Adj item: [Low],[Low’], [Center],[High’], [High]Press [Apply All]button to store theadjustment value.SSGAF VTVMOscilloscopePanel ANTUniversalconnectorPanel [Paneltuningmode][ ],[ ][PC testmode][ ],[ ]Write the value asfollowings.[L SENS2] / [Low]: 180 (Fixed)[L’ SENS2] / [Low’]: 180 (Fixed)[C SENS2] / [Cen-ter]: 175 (Fixed)[H’ SENS2] / [High’]: 175 (Fixed)[H SENS2] / [High]: 185 (Fixed)3) Adj item:[L SENS2]→[L’ SENS2]Adjust: [٭٭٭]Press [ ] key to storethe adjustment value.3) Adj item: [Low],[Low’]Press [Apply All]button to store theadjustment value.Write the value asfollowings.[L SENS2]/[Low]: 256[L’ SENS2]/[Low’]: 2564. RSSIreferenceadjust *5[AnalogNarrow]1) Adj item: [An RRSSI]Adjust: [٭٭٭]2) Adj item:[AnL RRSSI]→[AnL’ RRSSI]→[AnC RRSSI]→[AnH’ RRSSI]→[AnH RRSSI]Adjust: [٭٭٭]SSG output: 12dBSINAD level –3dB(MOD: 1kHz/±1.5kHz)1) Adj item:[RSSI Reference(Analog Narrow)]2) Adj item: [Low],[Low’], [Center],[High’], [High]SSG output: 12dBSINAD level –3dB(MOD: 1kHz/±1.5kHz)SSGDistortionmeterOscilloscopePanel ANTUniversalconnector[Panel tuning mode]After input signalfrom SSG, press[ ] key to store theadjustment value.[PC test mode]After input signalfrom SSG, press[Apply] button tostore the adjust-ment value.[AnalogWide]1) Adj item: [Aw RRSSI]Adjust: [٭٭٭]2) Adj item:[AwL RRSSI]→[AwL’ RRSSI]→[AwC RRSSI]→[AwH’ RRSSI]→[AwH RRSSI]Adjust: [٭٭٭]SSG output: 12dBSINAD level –3dB(MOD: 1kHz/±3kHz)1) Adj item:[RSSI Reference(Analog Wide)]2) Adj item: [Low],[Low’], [Center],[High’], [High]SSG output: 12dBSINAD level –3dB(MOD: 1kHz/±3kHz)[NXDNVeryNarrow]1) Adj item: [NvRRSSI]Adjust: [٭٭٭]2) Adj item:[NvL RRSSI]→[NvL’ RRSSI]→[NvC RRSSI]→[NvH’ RRSSI]→[NvH RRSSI]Adjust: [٭٭٭]SSG output: 12dBSINAD level for Ana-log Narrow –3dB(MOD: 1kHz/±1.5kHz)1) Adj item: [RSSIReference (NXDNVery Narrow)]2) Adj item: [Low],[Low’], [Center],[High’], [High]SSG output: 12dBSINAD level for Ana-log Narrow –3dB(MOD: 1kHz/±1.5kHz)Adjust with theanalog signal.*5: Because RSSI reference (NXDN Narrow) is adjusted by adjusting RSSI reference (Analog Narrow), it is not necessary to adjust RSSI reference(NXDN Narrow).