Kenwood TRC-80 Instruction Manual
Also see for TRC-80: Instruction manualService manual
                                 |
Group Communication Network ExamplePredetermined frequency 14.482 MHzYour Identification code 101Member 1 Identification code 102Member 2 Identification code 113Member 3 Identification code 114Group Group code 1**MANUALCALLING1 Adjust the SQUELCH control for the noise thresholdso the channel noise is just muted. ~2 Activate Selective Call via Menu No. 06.o "S.CALL" appears, and the receiveraudio ismuted.S.CALL -)I5 1 3 5 7 9 20 40 dBRF 103 Hold down Microphone PTT and enter a 3-digitIdentification code via the Microphone keypad.o To make a call with a Group code, use "*" as awild card.4 While still holding down Microphone PTT, enter "#".o You can release Microphone PTT immediatelyafter pressing "#".o The Identification code of the station being called(their individual code or a Group code) plus yourIdentification code is transmitted.o After the codes have been transmitted,the word"CALL" plus the Identification code of the stationthat was called are displayed. For example,"CALL 102".5 If you do not receive a response to your call withinabout 10, 20, or 30 seconds (Dealer selectable),your receiver mutes, and the radiotelephone is readyto receive a selective call.o Instead of waiting for the programmedtimeperiod to pass, you can also press [I] again(without pressing Microphone PTT) to restore theradiotelephone standby status.12MEMORYCALLING1 Adjust the SQUELCH control for the noise thresholdso the channel noise is just muted.2 Activate Selective Call via Menu No. 06.o "S.CALL"appears,andthe receiveraudioismuted.\S.CALL!S 1 3 5 7 9 20 40 dBRF 10\3 Hold down Microphone PTT , then enter "*" plus "A","B", "C", or "D". For example, "*A".4 While still holding down Microphone PTT, enter "#".o You can release Microphone PTT immediatelyafter pressing "#".o The Identificationcode that is stored in memoryA, B, C, or D plus the Character message that isstored for the same memory are sent. Forexample, the Identification code and Charactermessage stored in memory A are sent.o After the code and message have beentransmitted, the word "CALL" plus theIdentification code of the station that was calledare displayed. For example, "CALL 102".5 If you do not receive a response to your call withinabout 10,20, or 30 seconds (Dealer selectable),your receiver mutes, and the radiotelephone is readyto receive a selective call.o Insteadof waiting for 10 seconds to pass, youcan also press [I] again (without pressingMicrophone PTT) to restore the radiotelephonestandby status.RECEIVINGAdjust the SQUELCH control for the noise threshold sothe channel noise is just muted. After activatingSelective Call via Menu No. 06 and receiving a call, alertbeeps sound for about 10, 20, or 30 seconds (Dealerselectable). Stop these beeps by pressing any buttonor key. Pressing [I] stops the alert beeps and mutesthe receiver. Your Display may show either theIdentification code of the station calling you or aCharacter message that the caller has sent. Pressing[*] unmutes the receiver and allows you to monitorchannel activity.If you receive a call while scanning, the r~ceiverunmutes and stops on the channel for a period of time.Pressing Microphone PTT during this period cancels thealert beeps and the Scan function, and places theradiotelephone in the transmit mode; pressing [SCAN]cancels the alert beeps and the Scan function.-Your MenuMenu#07 101Menu#08 102Menu#09 113Menu#10 114Menu#11 1** |
Related manuals for Kenwood TRC-80
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine