Kenwood VRS-7100 Instruction Manual

Also see for VRS-7100: Service manual

Contents

46 ENChecking the codesThe 4-digit setup codes registered in the input selector keys can bechecked as follows.1Press the input selector key in which the setup code of thedesired component is registered.2Press and hold the Remote Setup key until the LED blinkstwice, then release the Remote Setup key.÷ Proceed to the next steps in less than 10 seconds after the LEDblinks twice.3Press the numeric key to enter "9 9 0".÷ The LED will blink twice.4Press the numeric key "1" once.The LED blinks for the same number of times as the numeral in thefirst digit of the 4-digit code. When the registered setup code is"1338", for example, the LED will blink once. If a code digit is "0", theLED will not blink.5Repeat step 4three more times for the remaining digit.Use "2" for the second digit, "3" for the third digit, and "4"for the fourth digit.Re-assigning device keysThe type of component device that can be registered is assigned inadvance in each input selector key, but this assignment can be changedas desired by the user.For example, the initial status is set so that a VCR can be registered in theinput selector VID1 key. If you want to register the setup code of a DVDplayer in the VID1 key just like in the DVD key, reassign the key (changethe registerable component type assignment for the input selector key)as described below.1Press and hold the Remote Setup key until the LED blinkstwice, then release the Remote Setup key.÷ Proceed to the next steps in less than 10 seconds after the LEDblinks twice.2Press the numeric key to enter "9 9 2".÷ The LED will blink twice.3Press the DVD key once, then press the VID1 key once.The LED blinks twice, and it is possible to register the setup codeof a DVD player in the VID1 key just like in the DVD key. Nowregister the setup code according to the model of the DVD player.The combination of components assignable to the input selectorkeys can be changed by pressing different keys in step 3. Forexample, to change the key assignment so that the same compo-nent as that registered in input selector "B" key can be registeredin input selector "A" key, press the "B" key then the "A" key afterentering "9 9 2" with the numeric keys.÷ For the originally assigned relationship between the input selector keysand system component types, see the table on the previous page.÷ To restore the original component type assignment of an inputselector key, press that input selector key twice after entering "9 9 2".÷ It is not possible to register a component in the TUNER key.Examples of key re-assignment and the order of pressing the keys:Registration of a DVD player in the VID1 keyTo change the VID1 key to another DVD:"9 9 2" \ "DVD" \ "VID1"Restoration of the original key assignmentTo return the VID1 key to the VID1 key:"9 9 2" \ "VID1" \ "VID1"Registration of a VCR in the VID2 keyTo change the VID2 key to another VCR:"9 9 2" \ "VID1" \ "VID2"Restoration of the original key assignmentTo return the VID2 key to the VID2 key:"9 9 2" \ "VID2" \ "VID2"Basic remote control operations for other componentsOperating other componentsThis operation lets you operate the registered components.1Use the Input Selecter keys to select the component you desire.When the input selector key is pressed, the system componentregistered in the pressed key becomes ready to be controlled. The inputselector of the receiver is also switched accordingly. If you want tocontrol the component registered in the remote’s input selector keywithout switching the receiver’s input selector to that source, press andhold the input selector key for more than 3 seconds.÷ To put the remote control unit to the receiver control mode, pressthe RCV Mode key.2Turn the component ON.÷ A DVD player, CD player, MD recorder or VCR registered in one of theremote’s input selector keys can be turned ON by pressing theremote’s SRC Power.÷ A TV registered in one of the remote’s input selector keys can beturned ON by pressing the remote’s TV Power key.3Press the operation keys you desire.÷ For the keys that can be used with each system component, seepages 58 to 59.Clearing all of the settings registered orstored in the remote control unitYou can reset the remote control unit to the initial status after purchase,clearing all of the component registration using setup codes and otherdata stored using the learning functions.1Press and hold the Remote Setup key until the LED blinkstwice, then release the Remote Setup key.÷ Proceed to the next steps in less than 10 seconds after the LEDblinks twice.2Press the numeric key to enter "9 8 1".÷ The LED blinks four times, and all of the data you registeredor stored in the remote control unit is cleared.SRC PowerInput selector keys