Magnavox 55MV314X Owner's Manual

Also see for 32MV304 F7: Quick start guide

Magnavox 55MV314X Owner's Manual Manual pdf 31 page image

Weak channel installationThis function lets you add the channels that were not added by theAutoProgram due to the reception conditions during the initial setup. Itis available only when you select Antenna in Installation mode.1 Use H I to Select Channels, then press OK.2 Use H I to select Weak channel installation, then press OK.● The PIN code will be required if you have locked channels.If Pin is forgotten go to Change PIN. L p. 293 Use J K to select channel Input box, then use H I to select achannel you want to memorize.4 Use J K to select Search, then press OK.5 Display will be changed to Store from Search when the channel isfound, then press OK.Note(s)● In most cases, Digital channels are not broadcast on the RF channel on which they appearon your TV. To add Digital channels you need to know the RF channel on which the Digitalchannel is being broadcast. (e.g. If there is a Digital channel 9.1 which is being broadcaston RF channel 25, you need to enter 25 while performing a weak channel installation.) Tofind out the RF channel on which a particular Digital channel is being broadcast, pleasecontact your local service provider. Installing Digital channels using Weak channelinstallation might not work for direct cable connections and if the Digital signal is too weakfor the TV to process.Installation mode1 Use H I to Select Channels, then press OK.2 Use H I to select Installation mode, then press OK.3 Use H I to select Antenna or Cable, then press OK.● When Antenna is selected, the TV detects antenna signals. Itsearches for DTV and Analog TV channels available in your area.● When Cable is selected, the TV detects signals supplied by cable.It searches for DTV, Analog TV and Cable channels available inyour area.Uninstall channelsThe channels selected here can be skipped when selecting the channelsusing CH + / –.Those channels can still be selected with the NUMBER buttons.1 Use H I to Select Channels, then press OK.2 Use H I to select Uninstall channels, then press OK.3 Use H I to select the channel you want to remove, then pressOK.● G indicates next to the Channel not skipped.● E indicates next to the skipped Channel.● The removed channels are not displayed on the list of Favoritechannels.● To reactivate a removed channel, use H I then press OK.PreferencesYou can set the unit to reduce the power consumption or adjust thebacklight brightness in Location setting when using the HOME feature ascompared to the RETAIL feature.fun-Link (HDMI CEC) allows you to operate your connected fun-Linkdevice when turned On.Setting your location to homeChoosing Home gives you full flexibility to change predefined settings forpicture and sound.1 Use H I to Select Preferences, then press OK.2 Use H I to Select Location, then press OK.Restore default settingsNetworkPreferencesChannelsLanguage RetailLocationfun-Link Controlfun-Link (HDMI CEC)OnE-sticker3 Use H I to Select Home, then press OK.RetailThe Unit will be set up with predefined settings forretail displays. In this setting, the Power Consumptionmay possibly exceed the limit requirement of theENERGY STARN qualification.HomeThis setting is ENERGY STARN qualified.The Unit is set to maximize the energy efficiency forHome setting and it can be adjusted through a choiceof Picture and Sound quality selections according toyour preference.Note(s)● You must set Home in the Menu. Otherwise, personalized Picture and Sound Settings willNot Be Memorized after the Unit goes into Standby Mode.● If you select Home, E-sticker will not be displayed.E-stickerWhen you set Location to Retail, E-sticker (Electronic Sticker) isdisplayed. E-sticker can be Turned Off using procedure below.1 Use H I to Select Preferences, then press OK.2 Use H I to select E-sticker, then press OK.3 Use H I to select Off, then press OK.31 .EnglishContinued on next page.