Makita DCU602 Instruction Manual

Also see for DCU602: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

23 ENGLISHInstalling or removing the carrierOptional accessoryInstalling the carrier1. Take out the carrier from the box, and attach theside rails and front rail to the base frame.► Fig.82. Tighten 6 thumb nuts together with springs andwashers to fix the rails.► Fig.9: 1. Thumb nut 2. Spring 3. Washer3. Place the carrier on the dump unit.Insert the bolt from the top. Attach the flat washer andspring washer in order to the bolt, and then tighten thenut from the bottom. Tighten the rest of the bolts andnuts in the same way.► Fig.10: 1. Bolt 2. Flat washer 3. Spring washer4. NutRemoving the carrierTo remove the carrier, perform the installation proce-dure in reverse.FUNCTIONALDESCRIPTIONCAUTION: Always be sure that the machine isswitched off and the battery cartridge is removedbefore adjusting or checking function on themachine.Installing or removing batterycartridgeCAUTION: Always switch off the machine andlock the brake lever before installing or removingof the battery cartridge.CAUTION: Always install the battery cartridgefully until the red indicator cannot be seen. If not,it may accidentally fall out of the machine, causinginjury to you or someone around you.CAUTION: Do not install the battery cartridgeforcibly. If the cartridge does not slide in easily, it isnot being inserted correctly.CAUTION: Do not use the high-temperaturebattery cartridge. When the high-temperature bat-tery cartridge is used, the machine stops automati-cally before a short beep sound is emitted, and maycause an injury.CAUTION: Be careful not to pinch your fin-gers when opening or closing the battery cover.NOTICE: Make sure that the cover of the batterybox is closed securely before use. Otherwise, mud,dirt, or water may cause damage to the product or thebattery cartridge.Installing the battery cartridge1. Pull up the lock lever, and then open the cover ofthe battery box.► Fig.11: 1. Cover 2. Lock lever2. Align the tongue on the battery cartridge with theslot on the battery box, and then slide the cartridge untilit locks in place with a little click.► Fig.12: 1. Battery cartridge3. Insert the lock key in the place shown in the figureas far as it will go, and turn it clockwise.► Fig.13: 1. Lock keyNOTE: To turn the lock key, insert the lock keycompletely.4. Close the cover of the battery box.► Fig.14: 1. CoverRemoving the battery cartridge1. Pull up the lock lever, and then open the cover ofthe battery box.2. Pull out the battery cartridge from the battery boxwhile sliding the button on the front of the cartridge.► Fig.15: 1. Button3. Turn the lock key counterclockwise, and pull it out.4. Close the cover of the battery box.Machine / battery protection systemThe machine is equipped with a machine/batteryprotection system. This system automatically cuts offpower to the motor to extend machine and battery life.The machine will automatically stop during operationif the machine or battery cartridge is under one of thefollowing conditions.A short beep sound or long beep sound is emittedbefore the machine stops automatically. The batteryindicators and lamps on the control panel blink while thebeep sound is emitted.NOTE: To cancel the beep sound, release the switchtrigger and pull the brake lever.Overload protectionWhen the machine/battery is operated in a mannerthat causes it to draw an abnormally high current,the machine automatically stops and the main powerlamp blinks in green. In this situation, turn the machineoff and stop the application that caused the machineto become overloaded such as reducing the loadedobjects. Then turn the machine on to restart.Overheat protectionWhen the machine is overheated, the machine stopsautomatically and the main power lamp lights up in red.In this case, let the machine and battery cool beforeturning the machine on again.