Makita DLS714 Instruction Manual

Also see for DLS714: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

Contents

18 ENGLISHremove particles adhering to the insides which mighthamper further collection.[Fig.36: 1. Dust bag 2. Dust nozzle 3. Fastener]NOTE: If you connect a vacuum cleaner to your saw,cleaner operations can be performed.Securing workpieceWARNING: It is extremely important to alwayssecure the workpiece correctly with the propertype of vise. Failure to do so may result in seriouspersonal injury and cause damage to the tool and/orthe workpiece.WARNING: When cutting a workpiece thatis longer than the support base of the saw, sup-port the entire length of the material beyond thesupport base and at the same height to keep thematerial level. Proper workpiece support helps toavoid blade pinch and possible kickback which mayresult in serious personal injury. Do not rely solely onthe vertical vise and/or horizontal vise to secure theworkpiece. Thin material tends to sag. Support work-piece over its entire length to avoid blade pinch andpossible KICKBACK.[Fig.37: 1. Support 2. Turn base]Vertical viseWARNING: Secure the workpiece firmlyagainst the turn base and guide fence with thevise during all operations. Otherwise the materialmay move during the cutting operation, cause dam-age to the blade, and be thrown which may result inloss of control and serious personal injury.Install the vertical vise on either the left or right side ofthe guide fence or the holder assembly (optional acces-sory). Insert the vise rod into the hole in the guide fenceor the holder assembly and tighten the lower screw tosecure the vise rod.[Fig.38: 1. Vise arm 2. Vise rod 3. Guide fence4. Holder 5. Holder assembly 6. Vise knob7. Lower screw 8. Upper screw]Position the vise arm according to the thickness andshape of the workpiece and secure the vise arm bytightening the upper screw. If the upper screw contactsthe guide fence, install the upper screw on the oppositeside of vise arm. Make sure that no part of the toolcontacts the vise when lowering the handle fully andpulling or pushing the carriage all the way. If some partcontacts the vise, re-position the vise.Press the workpiece flat against the guide fence and theturn base. Position the workpiece at the desired cuttingposition and secure it firmly by tightening the vise knob.Horizontal viseOptional accessoryWARNING: Grip the workpiece only when theindicator is at the topmost position. Failure to doso may result in insufficient securing of the workpiece.This may cause the workpiece to be thrown, causedamage to the blade or cause the loss of control,which may result in personal injury.[Fig.39: 1. Vise knob 2. Indicator 3. Vise shaft4. Base]The horizontal vise can be installed on the left side ofthe base.By turning the vise knob counterclockwise, the screwis released and the vise shaft can be moved rapidly inand out. By turning the vise knob clockwise, the screwremains secured.To grip the workpiece, turn the vise knob gently clock-wise until the indicator reaches its topmost position,then fasten securely. If the vise knob is forced in orpulled out while being turned clockwise, the indicatormay stop at an angle. In this case, turn the vise knobback counterclockwise until the screw is released, andthen turn it again gently clockwise.The maximum capacity of the horizontal vise is 120 mmwidth.Holders and holder assemblyOptional accessoryWARNING: Always support a long workpieceso it is level with the top surface of the turn basefor an accurate cut and to prevent dangerous lossof tool control. Proper workpiece support helps toavoid blade pinch and possible kickback which mayresult in serious personal injury.The holders and the holder assembly (optional acces-sory) can be installed on either side as a convenientmeans of supporting workpieces horizontally.Install them on the side of the tool, then tighten thescrews firmly to secure them.[Fig.40: 1. Holder 2. Holder assembly]When cutting long workpieces, use the holder-rodassembly (optional accessory). It consists of two holderassemblies and two rods 12.[Fig.41: 1. Holder assembly 2. Rod 12]

/ 164

Related manuals for Makita DLS714

Makita DLS714 Instruction Manual

This manual is suitable for:

DLS714

manualsdatabase

Your AI-powered manual search engine