National Instruments FieldPoint FP-3000 User Manual

Also see for FieldPoint FP-3000: Operating instructions

Contents

important information
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
about this manual
Overview of the FP-3000 Network Module
Fieldbus Network Setup
Features of the FP-3000 Network Module
Interoperability
Install the Device Description File
Figure
Updating the Device Description
Mount the FP-3000 and Terminal Bases
Connecting Terminal Bases with DIN Rail Mounting
Mounting the FP-3000 to a Panel
Connecting Terminal Bases with Panel Mounting
Mount I/O Modules onto Terminal Bases
Connect Power to the FP-3000
Power-On Self Test (POST)
LED Indicators
Table 2-1. Description of Fieldbus NETWORK LED States
HotPnP (Hot Plug and Play)
Updating the FP-3000 Firmware
Figure 2-14. FP-3000 Firmware Update Dialog Box
Figure 2-15. FP-3000 Search Dialog Box
Figure 2-16. Select FP-3000 Module Dialog Box
Initial Power On: Assigning Address and Device Tag
Getting Started
Assign a Tag to the New Block
Set the Input Range
Set Up Scheduling
Bring the Block Online
Taking Temperature Readings
Set the Input Range and Thermocouple Type
Controlling a Heating Element
Select the Module and Channel
PID Control
Connect the PID to the AI and AO Blocks
Tune the PID
Figure 3-5. High Limit Alarm Parameters Dialog Box
Figure 3-6. PID Alarm Connection Dialog Box
Block Overview
Resource Block
PID (Proportional–Integral–Derivative)
LOG (FieldPoint Log Block) (FP-3000 Specific)
Table 4-2. Function Blocks and FieldPoint Modules
Alarming
UNACKNOWLEDGED
Status and Mode Handling Overview
Quality
MODE_BLK Parameter and Mode Handling
Actual Mode
Permitted Mode
FP-3000 Specific Parameters
FIELDPOINT_CHANNEL
FP_AO_200_RANGE
FP_PWM_520_PERIOD
VERSION_INFORMATION
Simulate Enable
Write Lock
Fieldbus Communication Problems
Table B-1. Fieldbus Communication Problems
I/O Module Problems
Table B-3. Generic Software Configuration Problems
Table B-4. Resource Block Configuration Problems
ACK_OPTION
BINARY_OP
Table C-1. Error Codes
BLOCK_RESET
CLR_FSTATE
CONTROL_OPTS
DD_REV
FEATURE_SEL/FEATURES
FF_VAL
HARD_TYPES
L_TYPE
LIM_NOTIFY
LO_PRI
NV_CYCLE_T
OP_CMD_CXO
PV_FTIME
RCAS_OUT
RS_STATE
SHED_RCAS
SP_RATE_DN
STRATEGY
UPDATE_EVT
Cascade Initialization
Mode and Status Behavior during Cascade Initialization
Remote Cascades
Table D-
Mode Shedding Options
specifications
technical support resources

National Instruments FieldPoint FP-3000 User Manual Manual pdf 104 page image

Appendix D Advanced Function Block Behavior©National Instruments CorporationD-5FieldPoint FP-3000 User Manualtarget mode is changed at the time the block sheds mode, and the block doesnot attempt to enter the original lower priority mode when the shedcondition ends.Table D-1. Mode Shedding OptionsShed Option Behavior on Timeout DetectionShed to Manual The block enters Manual mode.Shed to Auto The block enters Auto mode.Shed to Retained The block sheds to the next highestpriority mode set in the target mode field.Normal Shed The block sheds to the next highestpriority mode set in the permitted modefield.

/ 118

Related manuals for National Instruments FieldPoint FP-3000

National Instruments FieldPoint FP-1000 User Manual

This manual is suitable for:

FieldPoint FP-3000

manualsdatabase

Your AI-powered manual search engine