NightStick FORTEM NSK-XPP-5466R Instruction Manual
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • USA • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.comINS-XPP-5466-LG-21 11-11-2020INSTALLING THE FORTEM ON TO THE HELMETImage 4 Image 5y Choose the side of the helmet you wish to mount the light on.y Rotate the mount to orient the clamp with thumbscrew on top.y Open the clamp completely and fully seat over helmet brim, ensuring the clamp clears anyrubber helmet trim. (Image 4)y Tighten the clamp fi rmly with included Allen wrench. (Image 5)SCAN FORMOUNTINGINSTRUCTIONVIDEOhttps://youtu.be/Ta0i7U-92hMSETTING THE ANGLE OF THE LIGHTy Twist the light left or right on the vertical pivot until beam pattern is in an ideal position.y The tension on the mount is meant to be fi rm to maintain the aim.y Once aimed, the mount allows the user to position light above or below the brim by rotatingup or down as needed.OPERATIONThe FORTEM has seven lighting modes:y Constant-on high-brightness fl ashlighty Medium-brightness flashlighty Low-brightness fl ashlighty Constant-on high-brightness fl oodlighty Medium-brightness floodlighty Low-brightness fl oodlighty Constant-on Dual-Light modeThe FORTEM has two switches, the fl ashlight switch (closest to the front of the light) andthe fl oodlight switch (closest to the rear of the light) providing access to all modes.CONSTANT-ON FLASHLIGHTPress the fl ashlight switch (closest to the front of the light) until it clicks and then releasefor constant-on flashlight in high-brightness mode. Press and release this same switch againto turn the light off.SELECT FLASHLIGHT BRIGHTNESS LEVELPress and hold down the fl ashlight switch. The fl ashlight will cycle from high to mediumto low and then back up again at a rate of approximately one mode per second. The light willcontinue to cycle up and down through the various modes as long as the flashlight switch isheld down. When the desired brightness level is reached, simply release the fl ashlight switch,and the light will remain in that brightness mode. Pressing and holding the fl ashlight switchagain will cause the light to cycle from whatever mode it is currently in. Press and release thefl ashlight switch to turn the light off.CONSTANT-ON FLOODLIGHTPress the fl oodlight switch (closest to the rear of the light) until it clicks and then releasefor constant-on fl oodlight in high-brightness mode. Press and release this same switch againto turn the light off.Instruction ManualFORTEM® XPP-5466US PATENT 9,713,217 AND 11,019,868THE XPP-5466 IS APPROVED FOR USECLASS I DIV 1 GRPS A-D T4CLASS II & III DIV 1 GRPS E-G T135°CCLASS I ZONE 0 AEx ia IIC T4 GaCLASS I ZONE 0 Ex ia IIC T4-20ºC ≤ Tamb ≤ +40ºC3.0V/Cell / Energizer 123E 467756INTRINSICALLY SAFESECURITE INTRINSEQUEConforms to:ANSI/UL STD 913, ANSI/UL 60079-0Certified to:CAN/CSA STD C22.2 No 157CAN/CSA STD C22.2 No 60079-0CAN/CSA STD C22.2 No 60079-11CSA STD C22.2 No 25Bayco Products, Inc. XPP-5466WARNINGS:Do not change batteries in hazardous location.Use only Energizer 123 BatteriesID 5012927WARNINGS - INTRINSICALLY SAFEy Warning: Use only the approved non-rechargeable batteries listed below.y Warning: Do NOT attempt to use rechargeable CR123A batteries with this light.y Warning: To prevent ignition of a hazardous atmosphere, do not open the batterycompartment in the hazardous environment. This task must ONLY be performed in an areaknown to be non-hazardous.y Warning: When exchanging batteries, use only ENERGIZER CR123A BATTERIES.y Warning: To prevent ignition of a hazardous atmosphere, the CR123A batteries must onlybe exchanged in an area known to be non-hazardous.y Warning: To reduce the risk of explosion, do not mix new non-rechargeable batterieswith used non-rechargeable batteries, or mix non-rechargeable batteries from differentmanufacturers.y Warning: Substitution of components may impair intrinsic safety.STROBE WARNINGExposure to strobing lights may cause dizziness, disorientation, and nausea. A very smallpercentage of people suffer from photosensitive epilepsy and may experience seizures orblackouts triggered by strobing lights. For more information from the EPILEPSY FOUNDATIONabout photosensitivity and seizures, please visit www.epilepsy.com. Anyone who has hadsymptoms linked to this condition should consult a doctor before using this product.SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETYFor personal safety, always confi rm the rating of any known hazardous or potentiallyhazardous location where the light is to be used.INSTALLING BATTERIES INTO THE FORTEMImage 1 Image 2 Image 3y To install the included CR123A Lithium Batteries in the FORTEM, begin by unscrewing thescrew on the battery compartment door. (Image 1)y Insert both batteries into the battery compartment paying attention to the battery orientationmarked on the back of the battery compartment door. (Image 2)y Re-install the battery compartment screw by pressing the door fully closed and thentightening the screw until it is hand tight. CAUTION: Do not cross-tread or strip the screwthreads. (Image 3)y Test the operation of the light (see OPERATION below). |
Related manuals for NightStick FORTEM NSK-XPP-5466R
NightStick FORTEM XPP-5466 Instruction Manual
NightStick Fortem XPP-5466 Instruction Manual
NightStick FORGE XPP-5465 Instruction Manual
NightStick XPP-5422 Instruction Manual
NightStick XPP-5420G Instruction Manual
NightStick XPP-5410G Instruction Manual
NightStick XPP-5420B Instruction Manual
NightStick XPP-5410G Instruction Manual
NightStick XPP-5412G Instruction Manual
NightStick XPP-5422B Instruction Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine