NightStick Fortem XPP-5466 Instruction Manual

Also see for FORTEM XPP-5466: Instruction manual Instruction manual

NightStick Fortem XPP-5466 Instruction Manual Manual pdf 1 page image

Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • USA • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.comINS-XPP-5466-16 09-27-2018fl ashlight produces 220 Lumens and is distance rated at 183 meters. The light is IP-X7waterproof and is drop rated at 2 meters.The Helmet Mounted Multi-Function Dual-Light Flashlight can be attached to eitherside of virtually any Fire Helmet or Hard Hat and provides a wide range of adjustabilityoptions. This adjustability allows the user to best position the light for purposes ofproviding clearance around face shields, goggles or other potential obstructions whilestill allowing the fl oodlight to point in a downward direction regardless of the angle of thebrim of the helmet.INSTALLING BATTERIES INTO THE 5466WARNING: In order to maintain the XPP-5466’s Intrinsically Safe rating, theonly CR-123 batteries certified for use with this light are the ENERGIZER 123BATTERIES.y Do not attempt to use any other brand or model of CR-123 batteries with this light.y Do not attempt to use any type of rechargeable CR-123 batteries with this light.Warning: To prevent ignition of a hazardous atmosphere, do not open the batterycompartment door in the hazardous environment. This task must ONLY be donein an area known to be non-hazardous.y To install the CR-123 Lithium Batteries in the 5466, begin by unscrewing the screwon the battery compartment door. (Image 1)y Using 2 – ENERGIZER 123 BATTERIES (make sure that both batteries are of thesame model), install the batteries in the back of the light paying close attention to themarkings inside the battery compartment for proper battery terminal polarity alignment.(Image 2)y Close the battery compartment door.y Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so may damage thethreads and impact the light’s Intrinsic Safety. (Image 3)Image 1 Image 2 Image 3ADJUSTING THE ORIENTATION AND/OR ANGLE OF THE MOUNTThe mount on the top of the light is designed to be adjustable in terms of which sideof the helmet it can be mounted to. Additionally, adjustments to the angle of the light canbe made to refine the angle of the beam in relation to the helmet. Out of the packaging,the mount is set up for attachment to the right side of the helmet. If the light needs to bemounted to the other side of the helmet or if the angle of the light needs to be adjusted,use the following steps to make those adjustments:Using the included 5/32” Allen Wrench, loosen and then remove the Angle LockSocket Head Cap Screw and separate the Mount from the rest of the assembly. (Image 4)If the angle of the light needs to be adjusted, loosen the Angle Adjustment SocketHead Cap Screw found below the Mount using the 5/32” Allen Wrench, adjust the angleas needed and then tighten the Angle Adjustment Socket Head Cap Screw completely.(Image 5)Reinsert the Mount into the rest of the assembly and reinstall the Angle Lock SocketHead Cap Screw paying close attention to the fact that the Mount is positioned correctlybased on the side of the helmet that the light is to be mounted to. (Image 6)NOTE: THIS PRODUCT IS NOT DESIGNED TO SWIVEL ONCE THE ANGLE OFTHE LIGHT HAS BEEN SET.Instruction ManualFortem™ XPP-5466US PATENT 9,713,217Please read these instructions before using your Nightstick XPP-5466. They includeimportant assembly and operating instructions.THE XPP-5466 IS APPROVED FOR USECLASS I DIV 1 GRPS A-D T4CLASS II & III DIV 1 GRPS E-G T135°CCLASS I ZONE 0 AEx ia IIC T4 GaCLASS I ZONE 0 Ex ia IIC T4-20ºC ≤ Tamb ≤ +40ºC3.0V/Cell / Energizer 1230359E 467756INTRINSICALLY SAFESECURITE INTRINSEQUEConforms to:ANSI/UL STD 913, ANSI/UL 60079-0Certified to:CAN/CSA STD C22.2 No 157CAN/CSA STD C22.2 No 60079-0CAN/CSA STD C22.2 No 60079-11CSA STD C22.2 No 25Bayco Products, Inc. XPP-5466WARNINGS:Do not change batteries in hazardous location.Use only Energizer 123 BatteriesID 4001184WARNINGS - INTRINSICALLY SAFEy Warning: Use only the approved non-rechargeable batteries listed below.y Warning: Do NOT attempt to use rechargeable CR-123 batteries with this light.y Warning: To prevent ignition of a hazardous atmosphere, do not open the batterycompartment in the hazardous environment. This task must ONLY be performed in anarea known to be non-hazardous.y Warning: When exchanging batteries, use only ENERGIZER CR-123 BATTERIES.y Warning: To prevent ignition of a hazardous atmosphere, the CR-123 batteries mustonly be exchanged in an area known to be non-hazardous.y Warning: To reduce the risk of explosion, do not mix new non-rechargeable batterieswith used non-rechargeable batteries, or mix non-rechargeable batteries from differentmanufacturers.y Warning: Substitution of components may impair intrinsic safety.STROBE WARNINGExposure to strobing lights may cause dizziness, disorientation, and nausea. A verysmall percentage of people suffer from photosensitive epilepsy and may experienceseizures or blackouts triggered by strobing lights. For more information from theEPILEPSY FOUNDATION about photosensitivity and seizures, please visit www.epilepsy.com . Anyone who has had symptoms linked to this condition should consult adoctor before using this product.SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETYFor personal safety, always confirm the rating of any known hazardous or potentiallyhazardous location where the light is to be used.PACKAGE CONTENTSy 1 – XPP-5466 Helmet Mounted Multi-Function Dual-Light Flashlighty 2 – CR-123 Lithium Batteriesy 2 – 5/16” - 18 x 1/4” Brim Mounting Allen Set Screws (installed in mount) – for FireHelmetsy 2 – 5/16” - 18 x 3/8” Brim Mounting Allen Set Screws (loose) – for Hard Hatsy 1 – 5/32” Allen Wrenchy 1 – Mounting shimAPPLICATIONThe XPP-5466 Helmet Mounted Multi-Function Dual-Light™ Flashlight is a singleself-contained fl ashlight, a fl oodlight and a Dual-Light mode fl ashlight designed forattaching to virtually any Fire Helmet or Hard Hat.Both the fl ashlight and the fl oodlight have user-selectable brightness levels andeach be operated independently or at the same time. In high-brightness mode, the