Nivus ocm pro cf Instruction Manual

Also see for OCM PRO CF: Instruction manual

Contents

Nivus ocm pro cf Instruction Manual Manual pdf 173 page image

Instruction manualOCM Pro CF®OCM Pro CF - Rev. 09 as of 07.06.2016 page 17316 EmergencyIn case of emergency- press the emergency-off button of the main system or- set the slide switch (see Fig. 7-35) on the unit to OFF.17 Dismantling/DisposalThe device shall be disposed according to the local regulations for electronicproduct.18 Table of PicturesFig. 2-1 OCM Pro CF nameplates ..................................................................................................................................12Fig. 2-2 Type key for OCM Pro CF measurement transmitters ......................................................................................13Fig. 3-1 Overview enclosure...........................................................................................................................................14Fig. 3-2 Overview sensors and electronic box................................................................................................................15Fig. 6-1 Possible combinations OCP type S4 / R4 .........................................................................................................20Fig. 6-2 Possible combinations OCP type M4 ................................................................................................................21Fig. 6-3 Basic design POA wedge sensor ......................................................................................................................21Fig. 6-4 Basic design CS2 wedge sensor ......................................................................................................................22Fig. 6-5 Basic design CSM wedge sensor V100 ............................................................................................................22Fig. 6-6 Overview radar, level sensor and holder ...........................................................................................................23Fig. 6-7 Measurement range of i-Series sensors ...........................................................................................................24Fig. 6-8 Situation at first signal reception .......................................................................................................................25Fig. 6-9 Situation at second signal detection ..................................................................................................................25Fig. 6-10 Echo signal images and evaluation ...................................................................................................................26Fig. 6-11 Investigated flow profile.....................................................................................................................................26Fig. 6-12 Computed 3-dimensional flow profile ................................................................................................................27Fig. 6-13 Measurement using the surface radar...............................................................................................................27Fig. 7-1 Wall mount enclosure........................................................................................................................................29Fig. 7-2 Wiring diagram wall mount enclosure OCM Pro CF ..........................................................................................33Fig. 7-3 Connecting a flow velocity or water-ultrasonic combi sensor on the OCM Pro type S4W0 / M4W0 .................34Fig. 7-4 Connecting a second velocity sensor to the OCM Pro type M4W0 ...................................................................34Fig. 7-5 Connecting a third velocity sensor to the OCM Pro type M4W0 .......................................................................34Fig. 7-6 Connection electronic box Type EBM with water-ultrasonic sensor Type CSM and air-ultrasonic sensorType DSM to Type S4W0 / M4W0 ....................................................................................................................35Fig. 7-7 Connection 2, electronic box Type EBM with water-ultrasonic sensor Type CSM to Type M4W0 ....................35Fig. 7-8 Connection 3, electronic box Type EBM with water-ultrasonic sensor Type CSM to Type M4W0 ....................35Fig. 7-9 Connecting a flow velocity sensor with integrated pressure measurement cell to type W0...............................36Fig. 7-10 Connecting an OFR flow velocity sensor to Type R4W0...................................................................................36Fig. 7-11 Connecting the air-ultrasonic sensor type LUS to type M4W0 / S4W0 ............................................................36Fig. 7-12 Connecting a 2-wire sensor (EX for level measurement) ..................................................................................37Fig. 7-13 Connecting a 2-wire sensor for level measurement to type W0 ........................................................................37Fig. 7-14 Connecting external level measurement from NivuMaster to type W0..............................................................38Fig. 7-15 Wall mount enclosure-connecting the overvoltage protection for power supply and analog inputs and outputs39Fig. 7-16 Overvoltage protection water-ultrasonic sensor or electronic box, wall mount enclosure .................................40Fig. 7-17 Overvoltage protection air-ultrasonic sensor, type OCL, wall mount enclosure ................................................40Fig. 7-18 Panel mount enclosure .....................................................................................................................................41Fig. 7-19 Wiring diagram OCM Pro CF panel mount enclosure .......................................................................................42Fig. 7-20 Connecting a flow velocity or water-ultrasonic combi sensor to the OCM Pro CF, type S4F0 / M4F0 ..............43Fig. 7-21 Connecting an OFR flow velocity sensor to Type R4F0 ....................................................................................43Fig. 7-22 Connecting a second flow velocity sensor to type M4F0...................................................................................43Fig. 7-23 Connecting a third flow velocity sensor to type M4F0 .......................................................................................44Fig. 7-24 Connection electronic box Type EBM with water-ultrasonic sensor Type CSM and air-ultrasonic sensorType DSM to Type S4F0 / M4F0 ......................................................................................................................44Fig. 7-25 Connection 2, electronic box Type EBM with water-ultrasonic sensor Type CSM to Type M4F0 .....................44Fig. 7-26 Connection 3, electronic box Type EBM with water-ultrasonic sensor Type CSM to Type M4F0 .....................45Fig. 7-27 Connecting a flow velocity sensor with integrated pressure measurement cell to type F0 ................................45Fig. 7-28 Connecting an air-ultrasonic sensor type OCL to type F0 .................................................................................45