Nuvo NV-D460 Installation Manual

Also see for NV-D2120: Installation guide Installation guide

Nuvo NV-D460 Installation Manual Manual pdf 8 page image

4ROUTPUT POWER OUTPUT POWER20W/6OHM X2 20W/6OHM X2SYS ONEXT. MUTELRLRLRVARIABLEOUTPUTFIXEDOUTPUTSUM13033118C USCONFORMS TOUL STD.6500CERTIFIED TOCAN/CSA STD.E60065NuVo Technologies Cincinnati Ohio USAFUSE:T5 A120V 60Hz 500WMODEL NV-I8DMSIX SOURCE EIGHT ZONEAUDIO DISTRIBUTION SYSTEMwww.nuvotechnologies.comOUTPUT POWEROUTPUT POWEROUTPUT POWER20W/6OHM X220W/6OHM X220W/6OHM X2TIP=LRING=RVARIABLEOUTPUTFIXEDOUTPUTTIP=LRING=RVARIABLEOUTPUTFIXEDOUTPUTTIP=LRING=RVARIABLEOUTPUTFIXEDOUTPUTTIP=LRING=RVARIABLEOUTPUTFIXEDOUTPUTTIP=LRING=RVARIABLEOUTPUTVARIABLEOUTPUTFIXEDOUTPUTFIXEDOUTPUTTIP=LRING=RTIP=LRING=R1 2 3 4 5 61 2 3 4 5 62 3 4 1 2 3RS-232CONNECT TONV-I8XUSE NV-SLC1CABLECONNECT TONV-I8XUSE NV-SLC1CABLECONNECT TONV-I8EZP1USE NV-NC1CABLEUSE CNLY WITH 250V FUSE4 5 6 SUM25 6 7 8OUTPUT POWER20W/6OHM X2ZONE 6ZONE 6 ZONE 7&8SYSTEMZONE TRIGGER OUTPUTSSOURCE LINKSOURCE INPUTSZONE 1NuVoNetEMITTER OUTPUTS DIGITAL LINKZONE 3 ZONE 4 ZONE 5ZONE 2 PROGRAM64 53 12SOURCE STATUS INPUTS1 2 3 4 5 6 7 8 9 10 11 12 14131Grand Concerto Back Panel1. These preamp lineouts are used for sending an audio signal to an external power amplifier. This is useful forlarge areas that require additional pairs of speakers. Use the variable output when you want the additional amplifier to becontrolled by the zone's Control Pad.2. These preamp lineouts are used for sending an audio signal to an external power amplifier when additionalspeakers are needed. This output is constant, so an amplifier connected to it will not change volume with that zone's ControlPad.3. The Grand Concerto will accept up to six audio sources. These are connected to the Grand Concerto amplifierwith standard stereo RCA cables.4. Six of the Grand Concerto's eight zones are amplified. These outputs accept 16-gage, two-conductor speakerwire and provide 40 watts per channel of power.5. This connection is used in conjunction with the Grand Concerto Expander System to create 16 total zones. Thesource link cable is supplied with the Expander System.6. These inputs are currently inactive on the Grand Concerto. They are intended for future use.7. These 12-volt outputs can be used to trigger an external device, such as an auxiliary power amplifier, foruse in a specific zone.8. IR signals received from the keypads are passed through the IR outputs to the source equipment using thesupplied IR emitters. Outputs 1-6 are routed to the corresponding sources, and the SUM outputs 1 and 2 are common and willpass all IR signals.9. This is a constant 12-volt output for turning on external equipment. There is no voltage output when the zones areoff.10. This input is designed to temporarily mute any audio playing through the system when the doorbell or phonerings. This works in conjunction with the NuVo NV-MI1 mute interface accessory. It also acts as a trigger for whole-housepaging through a phone system when set for this function in the Configurator Software.11. This RJ45 connection is the input for all zone information coming from the Grand Concerto Control Pads. Theconnection is made using the Network Cable supplied with the package.12. This connection is used in conjunction with the Grand Concerto Expander System to create 16 total zones. TheDigital Link cable is supplied with the Expander System.13. The bidirectional RS232 is a serial communication port that allows the Grand Concerto System to be controlled by anexternal home automation device. It is also used for configuration and programming purposes.14. A detachable power cord connects the system to an external AC power supply.Variable Output:Fixed Output:Source Inputs:Speaker Output:Source Link:Source Status Inputs:Zone Trigger Outputs:IR Emitter Outputs:SYS. ON:EXT. MUTE:Network Input:Digital Link:RS232:AC: