Oce im4511 Operator's Manual

Also see for im3511: Programming Date & Time Facsimile operation manual Operation manual Operating manual Operation manual

Contents

Oce im4511 Operator's Manual Manual pdf 14 page image

12GENERAL PROGRAMSSaddle stitch position adjustThis program is used to adjust the stapling position(folding position) when using the saddle stitch functionof the optional saddle stitch finisher.The value can be adjusted in 0.1 mm increments within±3.0 mm from the reference position for each papersize.[AUTOMATIC SADDLE STITCH] checkmarkThe saddle stitch print function can normally be dividedinto the following three general steps.1. The pages of the original are automaticallyreordered to allow saddle stitch binding (saddlestitch function).2. The pages are folded at the center.3. The paper is stapled at the center in two places(saddle stitch stapling).The [AUTOMATIC SADDLE STITCH] checkbox isselected by default.Selection of the checkbox assumes the use of theabove saddle stitch printing function (three steps).Saddle stitch stapling exceptionsDepending on the purpose of saddle stitch stapling, itmay be necessary to perform saddle stitch stapling onprinted matter that has already been bound by saddlestitching. In this case, it is necessary to disable step 1above. If you frequently perform this type ofexceptional saddle stitch stapling that requiresdisabling step 1, remove the checkmark from the[AUTOMATIC SADDLE STITCH] checkbox.High speed stackingThis program is used to have print speed priority, whichis available for printing in the offset mode with thesaddle stitch finisher.When this program is on, slight decrease of stackingperformance might occur.This program is set in the factory default setting.Auto paper selection settingUse this program to select the paper type* for which theautomatic paper selection function operates.Selections are "PLAIN PAPER", "PLAIN ANDRECYCLE PAPER", and "RECYCLE PAPER".* The paper type set for each paper tray in the papertray settings of the user settings (page 2-5 of the"Copying operation manual").Optimization of a hard diskThis is used to optimize the "Main folder" and "Customfolder" that are used for the document filing function.When this program is executed, a message will appearasking if it is okay to stop the job in progress. Touch the[YES] key to stop the job and begin optimization. Whenoptimization ends, the machine will restart if the powerswitch is switched on, or turn off if the power switch isswitched off.List printThis program is used to print lists and reports that canonly be printed from the key operator programs.• Touch the [KEY OPERATOR PROGRAMS LISTS]key to print one of the following groups:Copy, printer, fax/image send, document filing,general, security, all program lists• Touch a key other than the [KEY OPERATORPROGRAMS LISTS] key to begin printing a list orreport.1 2 1211Min.-3mmMax.+3mmReference positionPosition adjustedto the minusdirectionPosition adjustedto the plusdirection CAUTIONIf the power switch is switched off or the power plugis unplugged while optimization is in progress, thehard drive may be damaged and stored data orreceived data may be lost.NOTES About stopped jobsPrinting of received faxes and Internet-Faxes andtransmission of stored fax jobs will automaticallyresume after the machine restarts.For jobs other than the above (copy jobs, printjobs, document filing print jobs, etc.), the jobinformation is not retained and thus the stoppedjob must be executed again manually (forexample, the original for a copy job must beplaced again and the copy operation repeated). Operation after optimization startsUntil optimization finishes (or the [CANCEL] key istouched to cancel optimization),• The operation panel cannot be used, with theexception of the [CANCEL] key.• Operation from the Web page is not possible.• Faxes and Internet-Faxes cannot be received.• Print jobs will not be accepted.• The power will not turn off even if the powerswitch is switched off.• Auto power shut-off mode will not activate evenif the set time elapses. (Preheat mode willactivate.)