Oki B721 User Manual

Also see for B721: User manual User manual

Contents

Oki B721 User Manual Manual pdf 68 page image

- 68 -Installing a Printer Driver (for Windows)3 Printing●● Installing a Printer Driver (for Windows)If the printer is connected with the computerusing a USB or parallel cable, proceed to“Installing a Printer Driver” P.70.Preparations for NetworkConnectionInstalling a Printer Driver(for Windows)To complete the network connection with aWindows computer, first set IP addresses for theprinter, and then install a printer driver on thecomputer.If there is no DHCP server or BOOTP server onthe network, you need to manually configure theIP address on the computer or printer.If your network administrator or internet serviceprovider specifies an unique IP address for thecomputer and your printer, you need to set theIP addresses manually.Note● You need to complete the network setting of the computerbefore this procedure.● To complete this procedure, you must be logged in as anadministrator.● When setting an IP address manually, ask the networkadministrator or your internet service provider whichIP address to use. If the IP address is set wrong, thenetwork may go down or Internet access may be disabled.Memo● If configuring a small network consisting of only yourprinter and a computer, set IP addresses as shown below(according to RFC1918).For the computerIP address : 192.168.0.1 - 254Subnet mask : 255.255.255.0Default gateway : not usedDNS server : not usedFor the printerIP address Set : ManualIP address: 192.168.0.1 - 254 (select a differentvalue from that of the computer)Subnet Mask : 255.255.255.0Default Gateway : 0.0.0.0Network Scale : Small● To set [Network Scale], press the <ENTER> buttonand then select [Admin Setup] > [Network Setup] >[Network Scale]. First, Set the IP address of theprinter.1 Turn on the printer.2 Press the <ENTER> button on theoperator panel.3 Press the scroll button to select[Admin Setup], and press the<ENTER> button.䣈䣷䣰䣥䣶䣫䣱䣰䣵䢢䢢䢢䢢䢢䢢䢢䢢䢢䢴䢱䢵䣃䣦䣯䣫䣰䢢䣕䣧䣶䣷䣲䣒䣴䣫䣰䣶䢢䣕䣶䣣䣶䣫䣵䣶䣫䣥䣵䣃䣫䣴䣒䣴䣫䣰䣶䣏䣧䣰䣷䣵4 Enter the administrator password, usingthe ten-key pad.The factory default password is "aaaaaa". Press<ENTER> button after each character you input.䣇䣰䣶䣧䣴䢢䣒䣣䣵䣵䣹䣱䣴䣦䢪䢸䢯䢳䢴䣦䣫䣩䣫䣶䣵䢫5 Press the <ENTER> button.6 Check that [Network Setup] is selectedand press the <ENTER> button.䣃䣦䣯䣫䣰䢢䣕䣧䣶䣷䣲䢢䢢䢢䢢䢢䢳䢱䢷䣒䣣䣴䣣䣮䣮䣧䣮䢢䣕䣧䣶䣷䣲䣗䣕䣄䢢䣕䣧䣶䣷䣲䣒䣴䣫䣰䣶䢢䣕䣧䣶䣷䣲䣐䣧䣶䣹䣱䣴䣭䢢䣕䣧䣶䣷䣲