43856301TH Rev.3 93 /Oki Data CONFIDENTIAL 5. Maintenance Menu5.2 Maintenance UtilitiesThe maintenance utilities enables user to perform the adjustment shown in Table 5-2.Details of the maintenance utilities are available in the following documents.(1) Maintenance Utilities Operation Manual:42678801FUOI Rev18 and higher (Japanese)42678801FUO2 Rev18 and higher (English)(2) The maintenance utilities programs shown below.Applicable OS Filename Model numberWin9X/Me/NT/2000/XP(Japanese/English) MuWin.zip 42678801FW01 Rev18 andhigherTable 5-2 Maintenance utilities adjustment itemsItem Adjustment contentsMaintenanceUtilitiesOperationManual itemnumberOperation on theoperator panel(Item numbercorresponds to thatof the MaintenanceManual.)1 PU boardreplacement Copies the EEPROM data of the existingPU board.Adjustment objective: Copies theEEPROM data of the existing PU boardto the new PU board when the existingPU board needs to be replaced with thenew PU board during maintenance.Section2.4.1.1.1 Operation fromthe operator panelcannot be made.2 PU serialnumbersettingRe-writing the printer serial numbersaved in PU.Adjustment objective: When copyingthe EEPROM data of the PU board isnot possible (due to I/F error or others),re-write the serial number in the newreplacement PU board.Section2.4.1.1.2.1 Operation fromthe operator panelcannot be made.3 Factory/ShippingmodeSwitching between the Factory mode andthe Shipping mode.Adjustment objective: When copyingthe EEPROM data of the PU board isnot possible (due to I/F error or others),implement switching between the Factorymode and the Shipping mode. Whenthe replacement board is supplied formaintenance, it has been set in theFactory mode as the default setting.Switching from the Factory mode to theShipping mode needs to be performedusing this function.Section2.4.1.1.2.3 Section 5.3.2.10Item Adjustment contentsMaintenanceUtilitiesOperationManual itemnumberOperation on theoperator panel(Item numbercorresponds to thatof the MaintenanceManual.)4 CU boardreplacement Re-writing the EEPROM setup value ofthe CU board.Adjustment objective: Re-writes theEEPROM data of the existing CU boardto the new CU board when the existingCU board needs to be replaced with thenew CU board during maintenance.See note:Section2.4.1.1.3 Operation fromthe operator panelcannot be made.5 SerialnumberinformationsettingRe-writing the printer serial number,selections, output mode and printer serialnumber that are saved in CU.Section2.4.1.1.4.3 Operation fromthe operator panelcannot be made.6 Setupinformationof boarditemsVerifying the serial number informationand the Factory/Shipping mode. Section2.4.1.1.7 Operation fromthe operator panelcannot be made.7 USBsoftwareupgradeUpgrading the USB software Section2.4.2.2.1 Operation fromthe operator panelcannot be made.8 NIC softwareupgrade Upgrading the NIC software Section2.4.2.2.2 Operation fromthe operator panelcannot be made.9 NIC WebPageupgradeNIC Web Page upgrade Section2.4.2.2.3 Operation fromthe operator panelcannot be made.10 Mac addresssetting Setting the Mac address Section2.4.2.2.4 Operation fromthe operator panelcannot be made.11 ConsumableitemscountermaintenancefunctionCopies the consumable items counterdataDrum counter (Y, M, C, K)Fuser counterBelt counterToner counter (Y, M, C, K)Adjustment objective: Copies the data ofthe respective consumable item countersin the case when an existing consumableitem that is in the middle of its usage isremoved and installed in another printer.Section2.4.1.2.1 Operation fromthe operator panelcannot be made.Note! For the CU board of the C710, replace the entire EEPROM that is installedin CU using socket.