| 
– 155 –Chapter 7 Output and Screen Display — Screen status displayScreen status displayScreen display during shootingTCG 1 2 : 3 4 : 5 6 : 2 82160-59.94pMOV 420 150MA 3200KIP REMOTE36dBND:CLR1/10000F5.6+50H.SENS.DEC 3 1 2 0 1 9 1 0 : 4 5 : 3 0iZ123MF99D2xIR70%S/HINTRVLND1/16FLUO.999min999minS.SLOW120 FBCRELAYHDRSTDCH1CH2[ + ]ICONSVOLUME [ - ]1 2 3 5 6 7 8 9 10 11 12 1317 18 19 20 21 22 23 24 25 2637282931 4041422730383931434432333435364 14 15 161 Time codeThe display will toggle to the next display or no display every time the button is pressed.f [TCG **:**:**:**]: Displays the time code. [TCR **:**:**:**] will be displayed during playback.[TCG] is displayed with black and white inverted during the slave lock into the external input time code.f [UBG ** ** ** **]: Displays the user bits. [UBR ** ** ** **] will be displayed during playback.f [CLIP *:**:**:**]: Displays the counter value of each clip. This is displayed when the [RECORDING] menu → [REC COUNTER] is set to[CLIP]. Displays the counter value of the clip being played back during playback.f [*:**:**:**]: Displays the cumulative counter value from the reset position. This is displayed when the [RECORDING] menu → [RECCOUNTER] → [TOTAL] is set.2 Frame ratef [**fps]: Frame rate is displayed when set to the [SCENE FILE] menu → [VFR] → [ON].f [S.SLOW120]: Displayed when set to the [SYSTEM] menu → [SUPER SLOW] → [ON] and the [SYSTEM] menu → [FREQUENCY] → [59.94Hz].f [S.SLOW100]: Displayed when set to the [SYSTEM] menu → [SUPER SLOW] → [ON] and the [SYSTEM] menu → [FREQUENCY] → [50.00Hz].f (No display): It is not displayed when set to the [SCENE FILE] menu → [VFR] → [OFF] and the [SYSTEM] menu → [SUPER SLOW] → [OFF].3 switchDisplayed when the switch is set to .4 Message display area for stop of cooling fanDisplays a message when the cooling fan has stopped.5 Recording status (card slot 1)Displays the recording status of the memory card in card slot 1.f : Not target for recording.f (flashing): Recognizing the memory card.f : The recording is stopped while the recording target memory card is inserted.f : Recording.f (Flashing red dot): Processing to stop the recording.f [P ]: Recording is stopped with pre-recording is enabled and the recording target memory card is inserted.f [P]: Pre-recording is enabled, and the memory card is not inserted in the card slot, or the memory card is not recognized.f : The tally lamp is instructed to illuminate in red via network.f : The tally lamp is instructed to illuminate in green via network while the recording is stopped.f (No display): It is in one of the following conditions.- A memory card has not been inserted.- The memory card cannot be recognized.- The tally lamp is not instructed to illuminate in red/green via network, and the [NETWORK] menu → [NETWORK FUNC] → [NDI|HX] is set.6 Remaining recording capacity and status of the memory card (card slot 1)Displays the remaining recording capacity and status of the memory card in card slot 1.f [0min] to [999min]: Remaining recording capacity (999 minutes or more is displayed as [999min])- The display will flash when the remaining recording capacity becomes two minutes or less.- The recording capacity available for simultaneous recording (recording capacity for the memory card of the two memory cards with less recordingcapacity) is displayed when simultaneous recording is performed.f [WP]: Write protected (the write protection switch of the memory card is set to the LOCK side)f [END]: No remaining recording capacity (no remaining recording capacity on the memory card)f [ERR]: A memory card that cannot record is inserted (the card is recognized but cannot record due to a format error, a card other than a memorycard being inserted, etc.)f [!SDXC]: The SDXC memory card is not inserted for MOV recording |
