Panasonic AG-HMX100P Operating Instructions Manual

Also see for AG-HMX100E: Operating instructions Operating instructions Operating instructions

Panasonic AG-HMX100P Operating Instructions Manual Manual pdf 26 page image

26Basic OperationTo cancel the setting, press the key whileholding the SHIFT key.The display returns to the [SETUP] menu screen.To set the output of the AUX connector4HE!58CONNECTOROFTHE3$)/54CONNECTORSCANOUTPUTTHEINPUTSOURCEASISREGARDLESSOFTHE;!5$)/6)$%/=settings.Operate the rotary 4 control to select the input terminal towhich the source you want to output is connected.If [PGM], [PVW], or [M VIEW] is selected, the same sourceas that of the PGM, PVW, or MULTI VIEW connector is alsoOUTPUTFROMTHE!58CONNECTOR NOTEThe [AUX] settings are saved in different memory for thesrespective cases in which the system format setting isSD ( page 19) and HD (including 3D mode). The savedsettings are called according to the system format when it isswitched.No DVI-I input source can be selected.sTo set the input source for the waveformmonitor (WFM)Operate the rotary 5 control to select the input source forthe waveform monitor with multi-view output. NOTEThe [WFM] setting values are saved separately for therespective cases in which the system format setting is HD(including 3D mode) and SD. The saved values are calledaccording to the system format set in the [VIDEO FORMAT]submenu of the [SETUP] menu.Setting the Video Format[VIDEO FORMAT])TISNECESSARYTOMAKETHESETTINGSFORVIDEOSIGNALSOUTPUTFROMTHEUNITVIDEOFORMATSETTING ACCORDINGTOTHELOCATIONwhere this unit is used and the video output method.To set the video format for the entire system in this unitHEREINAFTERCALLEDhSYSTEMFORMATv USETHE;6)$%/&/2-!4=SUBMENUOFTHE;3%450=MENUIf the system format is changed, the current settings areINITIALIZEDTOCLEARTHESETTINGSINTHE;).46)$%/=MENU(PAGE ANDTHETITLEMEMORYSETTINGPAGE Rotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 507.54:316:9480/59i576/50i720/50p720/59p1080/50i1080/59iHDMIVIDEO 1080/59i 7.5SET UPFORMAT 16:9ASPECTAG-HMX100PRotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 507.54:316:9480/59i576/50i720/50p720/59p1080/50i1080/59iHDMIVIDEO 1080/59i 0SET UPFORMAT 16:9ASPECTAG-HMX100ETo select the aspect ratio7HENIORIHASBEENSELECTEDWITHTHEROTARY2 control, [4:3] or [16:9] can be selected with the rotary 3control.When the system format in which the aspect ratio cannotbe set has been selected, [---] appears.The factory default setting is [4:3].To select setup level (black level)7HENIHASBEENSELECTEDWITHTHEROTARYCONTROL [0] or [7.5] can be selected with the rotary 4 control.When the system format in which the setup level cannot bespecified has been selected, [--] appears.4HEFACTORYDEFAULTIS;=!' (-80 OR;=!' (-8% Changing the system format1 Select the system format that you want to setusing the rotary 2 control.If a setting value differing from the current systemFORMATISSELECTED ASTERISK ISADDEDTOTHEcurrent setting value.2 Press the key.3 When the message [OK?] appears, press thekey again.When the KEYISPRESSEDTOlXTHESELECTION because the signal format switching is performed,the operation of this unit is disabled for severalseconds.4 When the message “TURN POWER OFF”appears, turn off the power and restart the unit. NOTEIf other menu screen is displayed without fixing of the settingsson this screen, those settings are revoked and not applied.When 3D mode is set to other than [OFF], “--” appears andthe system format cannot be changed.If [HDMI] is selected, the HDMI input signal is output assis from the DVI-D OUT connector, disabling the AV mixerfunctions including video switching effects.