Panasonic AG-HMX100P Operating Instructions Manual

Also see for AG-HMX100E: Operating instructions Operating instructions Operating instructions

Panasonic AG-HMX100P Operating Instructions Manual Manual pdf 32 page image

32Basic Operation3 Set [FRAME] to the number of frames topreview using the rotary 3 control.To preview the movie, select a value equivalentto or smaller than the number of frames of themovie.4 To preview the still picture, select [FRAME](frame display) or [FIELD] (field display) usingthe rotary 4 control.To preview the movie, select [REPEAT] (repeatplayback) or [ONCE] (only-once playback)using the rotary 4 control.5 Press the key.$URINGSTILLPICTUREPREVIEW THESTILLPICTUREONTHEpage selected in above Step 2 is displayed.$URINGMOVIEPREVIEW THEMOVIECONTAINSFRAMESthe number of which is selected in Step 2 is playedBACK NOTEUpon save of a still picture or movie, set [MODE] to [EXIT] tosprevent the saved data from being overwritten.If you select [EXIT] during playback of a saved movie andspress the key, the image of the last frame is displayedand the playback of the movie stops.Even if other internal video (back matte or color bar) issselected in the [INT VIDEO] menu, [MEMORY] can beselected again to call the previously saved still picture ormovie. However, the saved still pictures and movies aredeleted when the power is turned off.To start/stop playback of a movie withoutusing the [INT VIDEO] menu1 Press the . (period) key while holding the SHIFTkey.2 Start playback in the confirmed playbackmethod for internal video.3 To stop playback, press the . (period) key whileholding the SHIFT key again.Using Video Input from PC [PC1]6IDEOCANBEINPUTFROM0#TOTHISUNITVIATHE$6) )).connector.For using video created on PC, it is necessary to allocateTHE$6) )INPUTTOANINPUTSOURCENUMBERINTHE;!5$)/6)$%/=SUBMENUOFTHE;3%450=MENUINADVANCE(PAGE The source input from PC is set from the [PC1] submenu ofthe [SETUP] menu.Rotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 5ANALOGDIGITALXGAWXGASXGA1080/50p1080/60p_ _ONOFFPC1 ANALOG A.SETFORMATSXGA ONTo select the DVI-I IN connector input3ELECT;!.!,/'=OR;$)')4!,=USINGTHEROTARYCONTROLTo select the input signal format3ET;&/2-!4=USINGTHEROTARYCONTROLThe source input from PC is displayed in the selectedSIGNALFORMAT(OWEVER ITISRESIZEDACCORDINGTOTHEsettings of the video format (PAGE To execute auto setup of analog inputSelect ON using the rotary 5 control, and press the KEY7HENTHEMESSAGE;/+=APPEARS PRESSTHE KEYAGAINTo cancel the execution, press the KEYWHILEHOLDINGDOWNTHE3()&4KEY NOTEWhen switching is being made between [ANALOG] ands[DIGITAL], the message “Please Wait…” appears, anddisappears upon completion of switching.When auto setup is executed, the image must be shown insthe entire display area of the screen. When auto setup isbeing executed, the message “Please Wait…” appears, anddisappears upon completion of auto setup.If auto setup is not successful, * appears under [A.SET].Auto setup may become unsuccessful due to insufficientautomatic screen adjustment depending on the input image.In this case, use the rotary 1 control to select [PC2] andadjust [H POSI], [V POSI], [PHASE], and [CLOCK].If the system format is 1080/50p or 1080/60p when DIGITALsor ANALOG is selected, auto setup is disabled. In this case,“---” appears under [A.SET].