Panasonic CQ-VA7300N Operating Instructions Manual

Contents

Panasonic CQ-VA7300N Operating Instructions Manual Manual pdf 26 page image

ACCBATTERY 15AABReverse Lead(Violet/white stripe)When connecting the rear view camera, use the reverse lead.Side Brake (Parking Brake) Connection Lead(Blue/yellow stripe)Be sure to wire the side brake (parking brake) for safety andpreventing accidents.External Remote Control Lead(Brown/black stripe)When using non-Panasonic external remote control, refer tothe manufacture for their product before connecting.External Amplifier Control Power Lead(Blue/white stripe)To an external amplifier.5149ENGLISH50ENGLISHCQ-VA7300N CQ-VA7300N50A8 (Black)A7 (Red)Resistor (220 Ω)A4 (Yellow)A5 (Blue)B8 (Green/black stripe)B7 (Green)B6 (White/black stripe)B5 (White )B4 (Gray/black stripe)B3 (Gray)B2 (Violet/black stripe)B1 (Violet )Not used.A5 : Motor Antenna Relay Control Lead(Blue)To Motor Antenna (Max. 500 mA).This lead is not intended for use with a switchactuated power antenna.Note: The power antenna extends automati-cally when the power of this unit is turnedon.A7 : Power Lead (ACC or IGN) (Red)To ACC power, +12 V DC.A8 : Ground Lead (Black)To a clean, bare metallic part of the car chassis.A4 : Battery Lead (Yellow)To the car battery, continuous +12 V DC.B8 : Rear Left –B7 : Rear Left +B6 : Front Left –B5 : Front Left +B4 : Front Right –B3 : Front Right +B2 : Rear Right –B1 : Rear Right +SpeakersB2B1B4B3B5B6B7B8Electrical ConnectionsCautions:¡Check the connectors provided on your car (seeprecaution below) before connecting the system.¡This unit is designed for use in a car having a 12-volt negative ground battery system.¡To prevent damage to the unit, be sure to followthe connection diagram.¡Strip about 5 mm of the lead ends for connection(only non-ISO connector cords).¡Do not insert the power connector into the unituntil the wiring is completed.¡Be sure to insulate any exposed wires to preventshort circuiting with the car chassis. Bundle allcables, and prevent cable terminals from touchingany metal parts.Precautions (ISO Connector)¡The pin arrangement of the power connectorconforms to ISO standard.¡The pin arrangement of ISO connectors in somecars may differ from the ISO standard.¡Please check that the pin arrangement of theconnector in your car conforms to ISO standard.¡For car types A and B, change the wiring of thered and yellow leads as shown at below.¡After connection, insulate the portions marked(C) with insulating tape.Note: For cars other than types A and B, pleaseconsult your local car shop.CCBATTERY 15AACCCCBATTERY 15AACCCCISOABStandard ISOCar Type ACar Type BBATTERY 15AACCA7: IGN or ACC switched 12 V supply(Red)(Yellow) (Yellow)(Red)(Red)(Yellow) (Yellow)(Red)(Red)(Yellow) (Red)(Yellow)A4: IGN or ACC switched 12 V supplyA4: +12 V Battery (Permanent supply)A7: +12 V Battery (Permanent supply)A7: +12 V Battery (Permanent supply)A4: No connectionA7A4Wiring DiagramCQ-VA7300NDisplay UnitCQ-VA7300NHide-away UnitAntennaTo remove the Fuse...312If the fuse (rear panel) blows fre-quently, they may be somethingwrong with the unit. Consult yournearest Panasonic Service Centrefor service.Fuse (15 A)!7 PowerConnectorFuse (15 A)@0 Display Unit/Hide-awayUnit Connecting Cord!7 Power Connector@1ISO AntennaAdapter(If needed)Cautions:¡Use ungrounded speakers only.Allowable input : 50 W or moreImpedance : 4 – 8 Ω¡Distance between speaker and ampli-fier: 30 cm or more¡Do not connect more than one speak-er to one set of speaker leads. (exceptfor connecting to a tweeter)