Panasonic DMR-E30 Operating Instructions Manual

Also see for DMR-E30: Operating instructions Installation instructions Operating instructions Bedienungsanleitung

Contents

17Auto Setup (without Q Link Functions) (continued)Removing InterferenceIn some cases, interference (lines or patterning) or a verypoor picture may appear on the TV when the DVD Recorder isconnected. If this happens, follow the steps below to changethe video playback channel (RF output channel) to remove theinterference.1 Switch [DVD, TV] (15) to “DVD”.2 Press [FUNCTIONS] (11) for more than 5 seconds.The RF output channel number is displayed on theunit display.3 Press the numeric buttons (4), [3, 4] (10) or[CH, W, X] (18) to select a channel number, whichdiffers by 2 or 3 from the present channel number.(For example, if the original channel number was28, enter 31.)≥Set the RF output channel of the DVD Recorder to [ss](RF OFF) when the DVD Recorder is connected to the TV viathe 21-pin Scart cable.Press the numeric (0) button (4) or [CH, W, X] (18) todisplay [ss]. Skip the step 4, if using a 21-pin Scart cable.4 Retune your TV until you receive the Test pattern. Itmay be necessary to repeat steps 2 and 3 aboveuntil you can see the Test pattern clearly.5 Press [ENTER] (10) to finish this setting.TV screenThe picture with interferenceUnit displayIndication when the RF outputchannel is 28 (example)Test pattern indicationRF OUTPUT CHANNELDVDCH : 28RETURNSELECTENTERIndication after changing the RFoutput channel to 31 (example)Unit displayTest pattern indicationRF OUTPUT CHANNELDVDCH : 31RETURNSELECTENTER 21 68(RF OFF)...The clear pictureFor the United Kingdom:This unit is not designed to control (switch on or change channel)your satellite receiver or Cable TV box, however, it can be taughtto recognise Video Plus+ Codes for Satellite stations. The Satellitereceiver or Cable TV box must be switched on and the correctstation selected. Some receivers have their own timer facility forthis purpose. Please refer to your Satellite Receiver/Cable TV boxinstructions for use of such timer facilities.For your unit to recognise the Video Plus+ Codes for each satellitestation, you must teach your unit which channel or AV input to recordfrom for the first time. Otherwise when setting a VIDEO Plus+ recording,the [ss] symbol will appear in the channel position indicating that theunit does not know which channel position to set. Once you have set thechannel/AV input once the unit will remember it whenever you use aVideo Plus+ Code for the station again.Preparation≥Turn on the television.≥Switch [DVD, TV] (15) to “TV”.1 Turn on the TV and the unit. Select video playbackchannel on the TV.2 Press [VIDEO Plus+] (2).3 Enter a Video Plus+ Code from a Satellite TV Guidefor a satellite channel, e.g. Sky 1 using the numericbuttons (4). If you make a mistake, use [2222] (10) togo back.4 Press [ENTER] (10). [ssssssss] will appear instead of achannel number/AV input.5 Use [3, 4, 2, 1] (10) to select the channel or AV inputthat is to be used for recording from the satellite channel.6 Press [ENTER] (10) to memorise the setting. Theunit will now automatically set the programmeposition or AV input correctly when a VIDEO Plus+recording is set for this satellite station in the future.7 Use [3333] (10) to select the programme that you havejust set. Now press [CANCEL] (5) to delete it fromthe timer recording list. It is no longer needed.8 Repeat steps 2ssss7 above until you have set anddeleted dummy timer recordings for each of thesatellite stations that you will make VIDEO Plus+recordings from.9 Press [RETURN] (23) when you have finished.RETURNNo.0:59 SPVIDEO Plus+ Remain12:53:00 16.7 TUE--0 9Enter VIDEO Plus+ Number by using 0-9 key.RETURNCANCELSELECT2:001:0016/ 7 TUEModeStopStartName Date1:58 SPTIMERRECORDING Remain1:19:00 16.7 TUEENTERSPPress ENTER to store new programme.PDCOFF64 ABCRETURNSELECTSP OK1:221:19ABC 16/ 7 TUE01Mode DiscspaceStopStartNo. Name Date1:58 SPTIMERRECORDING Remain1:19:00 16.7 TUEENTERNew Timer ProgrammeCANCELOFFPDCVideo Plus+ Codes for SatelliteReceivers/Cable TV