Panasonic KX-FP362BX Service Manual

6.2.3. SERVICE FUNCTION TABLECode Function Set Value EffectiveRangeDefault Remarks501 Pause time set X 100 msec 001~600 30 ----------502 Flash time X 10 ms 01~99 70 ----------503 Dial speed select 1: 10 pps2: 20 pps1, 2 1 ----------510 VOX time 1:6 sec 2:4sec 1, 2 1 ----------511 VOX sense 1:High 2:Low 1, 2 1 When the TAM (or EXT TAM) does not stoprecording the ICM because noise is detected onthe telephone line, change this setting to "LOW".514 Belldetectiontime X100msec 1~9 6 ----------520 CED frequency select 1:2100 Hz2:1100 Hz1, 2 1 See Symptom/Countermeasure Table for longdistance and international calls in THE UNIT CANCOPY, BUT CANNOT EITHERTRANSMIT/RECEIVE LONG DISTANCE ORINTERNATIONL COMMUNICATIONS (P.79).521 International mode select 1:ON 2:OFF 1, 2 1 See Symptom/Countermeasure Table for longdistance and international calls in THE UNIT CANCOPY, BUT CANNOT EITHERTRANSMIT/RECEIVE LONG DISTANCE ORINTERNATIONL COMMUNICATIONS (P.79).522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the default whentransmission is complete.523 Receive equalizer select 1: 0 km2: 1.8 km3: 3.6 km4: 7.2 km1~4 1 When the telephone station is far from the unit orreception cannot be performed correctly, adjustaccordingly.524 Transmission equalizer select 1: 0 km2: 1.8 km3: 3.6 km4: 7.2 km1~4 1 When the telephone station is far from the unit ortransmission cannot be performed correctly, adjustaccordingly.550 Memory clear See TEST FUNCTIONS (P.50).533 Setting the number of times thatmassage transfer is redialed.00~99 00~99 03 Selects the number of times that messagetransfer is redialed (not including the first dialing).534 Setting the massage transfer/pagercall redial interval001~999 sec 001~999 065 Sets the interval of message transfer/pager callredial.551 ROM check See TEST FUNCTIONS (P.50).552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See TEST FUNCTIONS (P.50).553 Monitor on FAX communicationselect1:OFF2:PHASE B3:ALL1~3 1 Sets whether to monitor the line signal with theunit´s speaker during FAX communication or not.554 Modem test See TEST FUNCTIONS (P.50).555 Scan check See TEST FUNCTIONS (P.50).556 Motor test 0 See TEST FUNCTIONS (P.50).557 LED test See TEST FUNCTIONS (P.50).558 LCD test See TEST FUNCTIONS (P.50).559 Document jam detection select 1:ON 2:OFF 1, 2 1 See DOCUMENT JAMS - SENDING (P.26).561 KEY test See TEST FUNCTIONS (P.50).570 BREAK % select 1:61% 2:67% 1, 2 1 Sets the % break of pulse dialing according PBX.571 ITS auto redial time set X number oftimes00~99 05 Selects the number of times that ITS is redialed(not including the first dial).572 ITS auto redial line disconnectiontime setX second 001~999 065 Sets the interval of ITS redialing.573 Remote turn-on ring number set X number ofrings01~99 10 Sets the number of rings before the unit starts toreceive a document in the TEL mode.580 TAM continuous tone detection 1:ON 2:OFF 1, 2 1 ON : Stops TAM operation when Dial tone, etc.are detected.590 FAX auto redial time set X number oftimes00~99 5 Selects the number of redial times during FAXcommunication (not including the first dial).591 FAX auto redial time disconnectiontime setX second 001~999 065 Sets the FAX redial interval during FAXcommunication.592 CNG transmit select 1:OFF2:ALL3:AUTO1~3 2 Lets you select the CNG output during FAXtransmission. ALL: CNG is output at phase A.AUTO: CNG id output only when automatic dialingis performed. OFF: CNG id not output at phase A.Refer to SOMETIME THERE IS A TRANSMITPROBLEM (P.77).48KX-FP362BX