Panasonic KX-FP362BX Service Manual

Code Function Set Value EffectiveRangeDefault Remarks593 Time between CED and 300bps 1:75 msec2:500 msec3:1 sec1~3 1 See Symptom/Countermeasure Table for longdistance and international calls in THE UNIT CANCOPY, BUT CANNOT EITHERTRANSMIT/RECEIVE LONG DISTANCE ORINTERNATIONL COMMUNICATIONS (P.79).Refer to RECEIVE PROBLEM (P.78) and THEUNIT CAN COPY, BUT CANNOT EITHERTRANSMIT/RECEIVE LONG DISTANCE ORINTERNATIONL COMMUNICATIONS (P.79).594 Overseas DIS detection select 1:detects atthe 1st time2:detects atthe 2st time1, 2 1 See Symptom/Countermeasure Table for longdistance and international calls in THE UNIT CANCOPY, BUT CANNOT EITHERTRANSMIT/RECEIVE LONG DISTANCE ORINTERNATIONL COMMUNICATIONS (P.79).Refer to SOMETIME THERE IS A TRANSMITPROBLEM (P.77) and THE UNIT CAN COPY,BUT CANNOT EITHER TRANSMIT/RECEIVELONG DISTANCE OR INTERNATIONLCOMMUNICATIONS (P.79).595 Receive error limit value set X Number oftimes001~999 100 Sets the number of acceptable error lines whenthe FAX reconstructs the received data. Refer toRECEIVE PROBLEM (P.78).596 Transmit level set X dBm - 15~00 10 Selects the FAX transmission level. Refer toSOMETIME THERE IS A TRANSMIT PROBLEM(P.77)and RECEIVE PROBLEM (P.78).598 Receiving sensitivity 43= -43 dBm 20~48 40 Used when there is an error problem. Refer toTHE UNIT CAN COPY, BUT CANNOT EITHERTRANSMIT/RECEIVE LONG DISTANCE ORINTERNATIONL COMMUNICATIONS (P.79).599 ECM frame size 1:256 byte2:64 byte1, 2 1 ----------717 Transmit speed selection 1:14400BPS2:12000BPS3:9600BPS4:7200BPS5:4800BPS6:2400BPS1~6 1 Adjusts the speed to start training during FAXtransmission. Refer to SOMETIME THERE IS ATRANSMIT PROBLEM (P.77) and THE UNITCAN COPY, BUT THE TRANSMISSION ANDRECEPTION IMAGE ARE INCORRECT (P.82).718 Receive speed selection 1:14400BPS2:12000BPS3:9600BPS4:7200BPS5:4800BPS6:2400BPS1~6 1 Adjusts the speed to start training during FAXreception. Refer to RECEIVE PROBLEM (P.78)and THE UNIT CAN COPY, BUT THETRANSMISSION AND RECEPTION IMAGE AREINCORRECT (P.82).722 Redial tone detect 1:ON 2:OFF 1, 2 1 Sets the tone detection mode after redialing.731 CPC mode 1:A 2:B 3:OFF 1~3 1 Sets the CPC signal detection mode from theconverter.732 AUTO disconnect cancel time 1:350 ms2:1.8 sec3:OFF1~3 1 “Set to “2” when the auto disconnect circuitoperates and cuts the line.”745 Power ON film feed 1:ON 2:OFF 1, 2 1 When the power is turned on, the film is wound totake up any slack.763 CNG detect time for friendlyreception1:10 sec2:20 sec3:30 sec1~3 3 Selects the CNG detection tone of friendlyreception.771 T1 timer 1:35 sec2:60 sec1, 2 1 Sets a higher value when the response from theother party needs more time during FAXtransmission.774 T4 timer X 100 msec 00~99 0 Use this function when delay occurs in the lineand communication (ex. Mobile comm) does notwork well.775 Monitoring of message transfer 1:ON 2:OFF 1, 2 2 If set to ON a message can be monitored fromthis unit´s SP-PHONE when transferring amessage.784 Voice prompt test You can hear the voice prompt from speaker afterpressing “START” key.815 Sensor & Vox check See TEST FUNCTIONS (P.50).841 Digital SP-phone check See DIGITAL SPEAKERPHONE (P.107).844 Original setting 1:NORMAL2:LIGHT3:DARKER1~3 1 Use this feature when you need to transmit andcopy a document with very faint writing or very darkwriting.NORMAL: Used for normal writing.LIGHT: Used for faint writing.DARKER: Used for dark writing.This feature will return to the normal mode aftertransmission or copying.852 Print test pattern See TEST FUNCTIONS (P.50).49KX-FP362BX