Panasonic KX-VC1300 User Manual

Also see for KX-VC1300: User manual Basic operation guide Basic operation gude User manual User manual

Contents

Panasonic KX-VC1300 User Manual Manual pdf 109 page image

Note• To continue setting another routing, repeatsteps 8–12.• The input "Destination" is converted to anetwork address and then used. There is noneed to register multiple destination IPaddresses that have the same networkaddress.13. Press [BACK].• The system settings screen is displayed.Making Connection SettingsNote• You can use the administrator menu to hide theconnection settings screen (Page 135).1. Select "Call set up" and press [ENTER].• The connection settings screen is displayed.2. Use [ ][ ] to select the following items for input:• The following items are displayed over 3 pages.To view all the items, press [R] to move to thenext page, and press [B] to move to theprevious page.Note• You must save the settings separatelyfor each screen on which you changedthe settings.• When "SIP" is set to "OFF" on the calltype settings screen (Page 128),"Encryption (SIP)" cannot be set.• When "H.323" is set to "OFF" on thecall type settings screen (Page 128),"Encryption (H.323)" cannot be set."Answer Mode": Use [ ][ ] to select how toanswer video conference calls ("Manual" [default],"Auto", or "Forced Answer") (Page 58)."More than one incoming call": Use [ ][ ] toselect whether to accept calls from Sub Sites tomake video conferences of more than 2 parties.– "ON" (default): Allow calls with more than 2parties.– "OFF": Do not allow calls to have more than 2parties.Note• For sites operating as "Main Sites" inmultiple-party video conference calls usingthe built-in MCU, select "ON"."Max. Bandwidth": Press [ENTER] and use [ ][ ] to select the maximum allowed bandwidth tobe used (256 kbps–18 Mbps) (default: 9.0 Mbps)."Max. Bandwidth Per Site (LAN 1)": Press[ENTER], and then use [ ][ ] to select themaximum bandwidth per site ("256 kbps" -"18 Mbps", or "Not Specified") (default: "NotSpecified")."Max. Bandwidth Per Site (LAN 2)" (KX-VC1600only): Press [ENTER], and then use [ ][ ] toselect the maximum bandwidth per site("256 kbps" - "18 Mbps", or "Not Specified")(default: "Not Specified").Note• For the KX-VC1300, "Max. Bandwidth PerSite (LAN 1)" is displayed as "Max.Bandwidth Per Site".• During a 2-party call, the bandwidth of thesite with the lowest-set maximumbandwidth is applied, and in a multiple-partycall, bandwidth is applied according to eachsite’s maximum bandwidth and the numberof connected sites. However, when thevalue of "Max. Bandwidth PerSite" (excluding "Not Specified") issmaller, the value of "Max. Bandwidth PerSite" is applied as the maximum bandwidth.• You cannot select a value that is higher thanthe maximum bandwidth set by the dealer.For details, contact your dealer."Dual stream": Use [ ][ ] to select whether dualstream communication is enabled.– "ON" (default): Enables dual streamcommunication.– "OFF" Disables dual stream communication."Send Content Method": Press [ENTER], andthen use [ ][ ] to select the contents sendingmethod when dual stream is enabled.– "Auto" (default): Automatically selects eitherdual stream or single stream.– "Single stream": Fixed to single stream."Encode rate": Press [ENTER] and use [ ][ ]to select the encoding rate ratio for the main streamand sub stream.– "Main (30%) < Sub (70%)": Prioritise the substream during calls.– "Main (50%) = Sub (50%)" (default): Use thesame priorities during calls.– "Main (70%) > Sub (30%)": Prioritise the mainstream during calls.Document Version 2015-12 User Manual 109Contacts and Settings