-47-RESET SPOT Alarm SuspensionThis function disables activation of the alarm linkand instead enables recording of any alarm activat-ed in the alarm log.It is used to suspend the alarm link during camerasetup.1. Press the RESET and SPOT buttons simultaneouslyfor more than two seconds to suspend the alarm.The LED on the RESET button lights up.2. Press the RESET button again to reset the alarmsuspension.The LED on the RESET button goes off.OTHER FUNCTIONS Recording on the Time LapseVCRThe following selections are made on the SETUPMENU described previously.Refer to the Recording Mode on page 28 for moredetails.1. Check the selected recording mode (MODE 0 -MODE 9).MODE 0: Normal Mode (Real Time)MODE 1 - 9: Time Lapse Mode (Linear Mode)If MODE 9 is selected, check the picture (Spot orQuad) to be recorded on the VCR.2. Press the Record button of the VCR to begin record-ing.Notes:• To let the VCR display the VCR menu for setup,select MODE 0 in the REC MODE SETUP menuof the Multiplexer.• While recording with the camera switching pulse(MODE 9), quad recording will work properlywhen the selected recording interval is morethan 0.11 seconds (less than 9 fields/s).• While recording without the camera switchingpulse (MODE 1 - 8), quad recording is not avail-able.When using a VCR whose recording interval is 2or 3 fields, select 4 fields (minimum) for the RECMODE parameter.However the same picture may be recordedrepeatedly. Camera Switching Pulse LossDisplay• When loss of the camera switching pulse is detect-ed, “SW LOSS” will blink on the monitor screen.• The buzzer does not beep.• When the camera switching pulse is recovered, “SWLOSS” is cleared from the monitor.Notes:• When MODE 0 to MODE 8 is selected forrecording, or MULTI 2 OUT for REC OUT, “SWLOSS” is not displayed because of the way thesystem application works.• If “ALARM” or “CH PP LOSS” is displayed onthe monitor screen, “SW LOSS” is not displayedbecause alarm has priority.

PREFACE

PRECAUTIONS

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

INSTALLATIONS

dip switch setting

SYSTEM CONNECTIONS

connection with the time lapse vcr

SETUP MENU

Alarm Setup Menu

alarm buzzer duration

Multiscreen Output Menu

camera display position setting

Spot Output Setup

recording mode

Multiscreen 2 Output Setup

System Setup

camera title display position

lock mode

alarm terminal setup

communication port setup

Camera Download

Camera Upload

OPERATING PROCEDURES

CAMERA CONTROL FUNCTION

camera setup

ALARM CONTROL FUNCTION

example of using multiscreen 2 monitor

OTHER FUNCTIONS

SETUP MENU OPERATIONS (with WV-CU550A)

OPERATING PROCEDURES (with WV-CU550A)

SYSTEM EXPANSION

APPENDIX

command table

SPECIFICATIONS

Panasonic WJ-FS616C Operating Instructions Manual

WJ-FS616C

operating instructions

IMPORTANT SAFETY INSTRUCTIONS

Rear View

INSTALLATION

Tally Output Setting

DIP Switch Setting

Mounting into the Rack

CONNECTIONS

Connection with the Camera Sites

Connections for RS-485 type camera

Connection with the Monitors

Connection with Alarm Sensors

spot and multiscreen monitor

Connection with the Time Lapse VCR

SETUP PROCEDURES

Spot and Multiscreen Monitor

Programming Setup Menu

ALARM SETUP

Camera Site Alarm

Alarm Mode on the Multiscreen Monitor

MULTISCREEN OUTPUT SETUP

Camera Display Position Setting

SPOT OUTPUT SETUP

RECORD OR MULTISCREEN 2 OUTPUT SETUP

SYSTEM SETUP

Camera Title Setup

Sequence Timing (Multiscreen Monitor)

Cable Compensation/VD2/Data

Playback Mode

VCR Input Select

Password

OTHER SETUP MENUS

All Reset

CONTROLLING THE VIDEO INPUT AND MONITORS

Controlling the Multiscreen Monitor

Controlling the Playback Images

Displaying the Camera and Playback Images

Alarm Reset

Alarm Suspension

OTHER FUNCTION

OPERATING PROCEDURES (with WV-CU550C)

SYSTEM CONTROLLER WV-CU550C

Installations

SETUP MENU OPERATIONS (WITH WV-CU550C)

FUNCTION OPERATIONS (WITH WV-CU550C)

Camera Selection

Operating Procedure

STANDARD ACCESSORIES

WJFS616 - SWITCHER