Panasonic WJ-NV300K Installation Manual

Also see for WJ-NV300K: Operating instructions Quick reference guide Operating instructions

Panasonic WJ-NV300K Installation Manual Manual pdf 42 page image

42Step 6Click the [Next] button.IP address will be given to the cameras newly con-→→nected, replaced or added, and the images from thecamera will be displayed on the operational screen.Note:On "Easy Start", it is impossible to register the cameras•in other subnets via the same router.For the security enhancement, changing of the IP•address of the camera will become impossible when 20minutes have passed after the power is turned on.Perform the camera detection within 20 minutes, or turnoff the power of the camera and turn it on again if morethan 20 minutes has passed. Refer to the operatinginstructions of the camera for further information.When 20 minutes have passed after the power of thecamera is turned on, "ONVIF" may be detected depend-ing on the models of Panasonic cameras. In such acase, turn off the power of the camera and turn if onagain to perform the camera detection.When "On" is selected for the "DHCP" setting of the•detected cameras, the recorder will forcibly change thesetting to "Off" to give the IP addresses automatically.When the [Cancel] button is clicked, the top screen of•"Easy Start" (the menu to set the date & time) withoutapplying the camera detection result will be displayed.Step 7When you wish to change the registered camera numbers, itis possible to change the order of the camera numbers.Images from the cameras will be displayed on the monitorfrom the upper left corner to the right in order of the cameranumber (1, 2 ... 16: The monitor screen will change accord-ing to the number of the camera in use; 9 cameras on9-screen, 16 cameras on 16-screen, and 24 or 32 camerason 2 of 16-screen)To interchange camera numbers, drag the camera image tobe moved with the mouse and drop on the desired position.If the camera titles are to be interchanged as well, mark the"Also change camera titles" checkbox.[Camera status]The model numbers and statuses of each camera will bedisplayed in a list.Displaying image: Displays the images from the camerausing the IP address that is newly registered or thathas already been registered.Changing IP address: Images are being obtained fromthe camera whose IP address has been changed.Note:Before the settings, register the cameras into the net-•work. Only the cameras added by license registration willbe detected even though more cameras than the regis-tered license number are connected.It is recommended to disconnect unnecessary cameras.Cameras shall be connected to the Camera/PC port.•Cameras will not be detected if they are connected tothe PC port.[New] buttonDetects all the connected cameras.The models and results of the detected cameras will be dis-played.Make sure that the model numbers of all the connectedcameras are being displayed.[Addition] buttonDetects only the added or replaced cameras.The models and results of the detected cameras will be dis-played.Make sure that the model numbers of all the added orreplaced cameras are being displayed.Important:The system will assign new IP addresses to all the con-•nected cameras (including currently-operated cameras)by clicking [New] button.Cameras newly added after the operation start will be•registered in the default settings. To conform the set-tings to those of the registered cameras, perform thesettings for the added cameras.For the video encoder (WJ-GXE500), only the camera•connected to CH1 will be detected. The channels CH2to CH4 are needs to be registered from the setup menu.[Camera]Up to 32 cameras can be connected. After the license isregistered (☞ page 36), 16, 24 or 32 cameras can be con-nected.[Model]When Panasonic cameras are used, the model numbers willbe displayed.[Results]New: Displayed when the camera is newly connected tothe recorder.Replaced: Displayed when the camera has beenreplaced by another one.Added: Displayed when the camera connection is addedto the recorder.Registered: Displayed when the camera has alreadybeen registered.Lost: Displayed when the registered camera is notdetected.Blank: No camera is detected.Note:If "Lost" is displayed or the column is left blank, check if•the power of the camera is turned on, and make surethat cables are properly connected.