Philips BDL4677XH User Manual

Also see for Signage Solutions BDL4677XH: Brochure & specs

BDL4677XH19• The PIP function is available only for certain signal sourcecombinations as shown in the table below.• The availability of the PIP function will also depend on the resolutionof the input signal being used.Main PictureSub Picture Displayport HDMI DVI-D VGA YPbPr Video CardOPSDisplayport X X X O O O XHDMI X X X O O O XDVI-D X X X O O O XVGA O O O X X X OYPbPr O O O X X X OVideo O O O X X X OCard OPS X X X O O O X(O: PIP function available, X: PIP function unavailable)By pressing the [PIP ON/OFF] button on the remote control, you canchange the mode in the order shown below:PIP POP PBP aspect PBP full OffThe resolutions in the PIP and POP modes are configured as follows:PIP SIZE {Small} : 320 x 240 pixels{ Medium} : 480 x 320 pixels{ Large} : 640 x 480 pixelsPOP SIZE : 474 x 355 pixelsNOTE: The images displayed in the sub picture always fit the PIPsizes shown above irrespective of the aspect ratio of the inputimage.4.2.5. Configuration1 menuSwitch on stateAuto adjustPower saveLanguageColor systemPictureScreenAudioPIPConfiguration1Configuration2Advanced optionPanel savingNetwork control portNetwork settingsConfiguration resetFactory resetSwitch on stateSelect the display status used for the next time you connect the powercord.• {Power off} - The display will remain off when the power cord isconnected to a wall outlet.• {Forced on} - The display will turn on when the power cord isconnected to a wall outlet.• {Last status} - The display will return to the previous power status(on/off/standby) when removing and replacing the power cord.Auto adjustUse this function to automatically optimize the display of VGA inputimage.NOTE: This item is functional for VGA input only.Power saveUse this setting to reduce the power automatically.• {RGB} - Select {On} to let the display enter Power save modewhen no signal is detected from the HDMI Graphic mode, DVI-D,or VGA inputs after three successive cycles.• {VIDEO} - Select {On} to enter power saving mode when nosignal is detected from the HDMI Video mode, Video input, orComponent inputs after three successive cycles.LanguageSelect the language used in the OSD menu.The options are: { } / { } / { 简体中文 } / { } /{ } / { } / { } / { } / { } / { 繁體中文 } /{ }.Panel savingChoose to enable the panel saving functions and thus reduce the risk of“image persistence” or “ghost-imaging”.• {Cooling Fan} - Select {On} to turn on the cooling fan all thetime. Select {Auto} to turn on/off the cooling fan according to thedisplay’s temperature.NOTES:• The default {Auto} option will start running the cooling fan ifthe temperature of 60°C (140°F) is reached, and stop runningthe cooling fan if the temperature of 58°C (136°F).• A temperature-warning message will be shown on the screen ifthe temperature reaches 69°C (156°F). All key functions except[Power] key will then be disabled.• Once the temperature reaches 70°C (158°F), the display powerwill be shut down automatically.• {Brightness} - Select {On} and the image brightness will be reducedto an appropriate level. The Brightness setting in the Picture menuwill be unavailable when selected.• {Pixel shift} - Select the time interval ({Auto} / {10 ~ 900} Seconds/ {Off}) for the display to slightly expand the image size and shiftthe position of pixels in four directions (up, down, left, or right).Activating Pixel Shift will disable H Position, V Position and ZoomMode in the Screen Menu.Color systemSelects the Color System depending on your input video format.The options are: {Auto} / {NTSC} / {PAL} / {SECAM} / {4.43NTSC} /{PAL-60}.NOTE: This item is functional for VIDEO input only.Network control portSelect the network control port.Choose from: {RS232} / {LAN(RJ45)} / {Card OPS RS232}.NOTES:• If {LAN(RJ45)} is selected, then {RS232} will not be activated, evenif a cable is attached, and vice versa.• The option {Card OPS RS232} is functional after connected withyour OPS device.