Raleigh Fast Pedelec User Manual

Also see for Bosch Cruise: Instrucoes de Utilizacao

Contents

Raleigh Fast Pedelec User Manual Manual pdf 230 page image

30 VIII User Manual Pedelec Xion10 Cleaning› Remove the battery before you clean yourPedelec.› Do not use benzine, thinner, acetone or similaragents in the cleaning procedures under anycircumstances. Likewise, the use of abrasivecleaners and aggressive cleaning agents mustalso be avoided.› Only use commercially available, householdcleaning agents and disinfectants (isopropylalcohol) or water. You can obtain suitable clean-ing agents and additional information from yourspecialist cycle shop.› We recommend you clean your Pedelec with adamp cloth, a sponge or a brush.10.1 Cleaning the batteryMake sure when cleaning that water does not enter thebattery. Although the electrical components are sealed,it is not advisable to clean the bike by spraying it with ahose or a high-pressure cleaner. This could damage yourbike.When wiping down the battery, be careful not to touch andconnect the contacts on the underside. This could causethe battery to switch off.10.2 Cleaning the motorDirt should be removed from the motor of your Pedelecregularly, ideally using a dry brush or a damp (not wet)cloth. Running water such as that from a hose pipe or evena high-pressure cleaner must not be used for cleaning.The ingress of water can destroy the motor. Therefore,ensure that neither fluids nor moisture enter the motor atany time during cleaning.Do not clean the motor when it is warm, e.g. immediatelyafter a trip. Wait until it has cooled down. Otherwise, themotor may be damaged.9.2 Installing the rear wheel1. Place the torque support on the left axle side of themotor (see point 2 in the image below).2. Then feed the rear wheel past the rear derailleur andinto the dropout on the frame.3. If your Pedelec has disc brakes, ensure that the brakedisc is placed exactly in the centre between the brakeblocks.4. Insert the rear wheel in the dropout so that the torquesupport fits exactly and the ends of the axle sit entirelywithin the dropout.5. Close the quick-release device (➠ General User Manu-al, Chapter 18.6.2 “Inserting the rear wheel ”).6. Connect the cable between the motor and the battery.7. Attach the plug to the chain stay once moreusing the rubber ring.8. If your Pedelec has rim brakes, engage the brake cableonce more.For precise details regarding the handling of rim ordisc brakes and quick-release devices, please refer tothe section of the User Manual concerning the tech-nology featured in the bike.Placing the torque supportMotormontage - BremsseiteMotor mounting - side of the brakeALBER-KomponentenKomponenten anderer Hersteller[1] Motor[2] Drehmomentstütze in der von Ihnen bestellten Variante (Abweichung zur Grafik möglich)Rahmen des Fahrrads[3] Unterlagscheibe[4] Mutter,[5] Bremsscheibe[6] Bremsensatz[7]Anzugsmoment: 20 NmACHTUNG: Zuerst die Mutter auf der gegenüberliegenden Seite anziehen, danach diese Mutter!Bitte beachten Sie bei Ihren Arbeiten die Vorgaben und Empfehlungen des jeweiligen Herstellers zurMontage seiner Komponenten.ALBER ComponentsComponents of other manufacturers[1] Motor[2] Torque receiver in the version ordered (might differ from drawing)[3] Washer[4] Nut,[5] Brake disc[6] Brake set[7] Bicycle framefastening torque: 20 NmPlease pay attention to the instructions of each manufacturer for the assembly of the appropriatecomponents.ATTENTION: Tighten this nut after the one on the opposite!56341274