Reece Myzone3 Series User Manual

Contents

Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Installation
Myzone Naked 405 — Wiring layout for up to 8 zones
Myzone Naked 410 — Wiring layout for up to 8 zones
Myzone Naked 415 — Wiring layout for up to 8 zones
Myzone Naked 415 —Wiring layout for up to 14 zones
Myzone Nano 420 — Wiring layout for up to 8 zones
Myzone Nano 420 —Wiring layout for up to 14 zones
Myzone Nano 425 —Wiring layout for up to 14 zones
Myzone Nexus 435 —Wiring layout for up to 14 zones
Optional equipment for wireless temperature controlled zones
Optional equipment for wired temperature sensors
Myzone 415 to 435 — Optional equipment for iSave addition (up to 6 zones)
Optional equipment for Ethernet Home Automation connection
Integrated Myzone A/C, Lights, Irrigation & Security
Myzone wiring connection to AC units
Myzone wiring connection to Actron units
Myzone wiring connection to Haier units
Myzone wiring connection to Hitachi units
Myzone wiring connection to Kaden units
Myzone wiring connection to Kelvinator units
Myzone wiring connection to LG units
Myzone wiring connection to Midea units
Myzone wiring connection to Rinnai units
Myzone wiring connection to Samsung units
Myzone wiring connection to Temperzone units
Myzone wiring connection to York units
Myzone wiring connection to Universal Control Module
Universal Control Module—Gas heating thermostat only
Universal Control Module—1 stage gas heating + 1 x fan speed
Universal Control Module—1 stage gas heating + 1 stage cooling + 1 x fan speed
Universal Control Module—2 stage gas heating + 1 stage cooling + 1 x fan speed
Universal Control Module—2 stage gas heating + 2 stage cooling + 1 x fan speed
Universal Control Module—1 stage reverse cycle heat pump + 1 x fan speed
Universal Control Module—1 stage reverse cycle heat pump + 3 x fan speed
General installation instructions
System initialisation
During initialisation
System Configuration
Configuration main menu
Zone setup
Sensor configuration
Pairing and configuring Myzone RF sensors
Sensor calibration
iSense controller configuration 4
AC unit configuration
Fan auto configuration
Fan auto zone area setup
Master / Slave setup
WiFi bridge configuration
Manual IP configuration
WiFi connection
Home automation integration
Myzone Naked 410 remote— Configuration
User Manual
Myzone 410—435 home screen
Zone control
Edit zone names and settings
Adjusting temperature controlled zones
Zone airflow summary
Changing zone airflows
Favourites
Assigning and editing favourites
Schedules
Setting and editing a schedule
Setting the time
Changing the home screen colour
iSense controller
Further assistance

Reece Myzone3 Series User Manual Manual pdf 38 page image

381.30.1 Myzone - Wiring connection to Actron unitsUnit Make ConnectionActron ( Ultra Slim low profile series only)Indoor Model / Outdoor modelLRE-071AS / URC-071AS ( 7kw )LRE-100AS / URC-100AS ( 10kw )LRE-130AS / URC-140AS (14kw )1. Connect a shielded, 2 core, twisted pair control cable from the CM225 / CM325A to theX / Y in the fan coil unit. (This cable and connector is supplied by Actron). Polarity iscritical see Fig (i) (J) & (K) below, for correct connection.X Y E +12VCN40 Connector Pin outFig (i) - Indoor fan coil unitterminals X YFig (J)Shielded, 2 core,twisted pair controlcable (not supplied)Fig (K) - Myzone CM225 / CM325ACorrect polarityYX

/ 104

This manual is suitable for:

Myzone Naked 400 Myzone Naked 405 Myzone Naked 410 Myzone Naked 415 Myzone Nano 420 Myzone Nano 425 Myzone Nano 430 Myzone Nexus 435 Myzone3 Series

manualsdatabase

Your AI-powered manual search engine