Regency P33-LP10 Owners & Installation Manual

Regency P33-LP10 Owners & Installation Manual Manual pdf 41 page image

Regency ® P33-10 Zero Clearance Direct Vent Gas Fireplace | 41|41operating instructionsFIRST FIREThe first fire in your fireplace is part of the paintcuring process. To ensure that the paint is properlycured, it is recommended that you burn your fireplacefor at least four (4) hours the first time you use itwith the fan on.When first operated, the unit will release an odourcaused by the curing of the paint, the burning offof any oils remaining from manufacturing. Smokedetectors in the house may go off at this time. Opena few windows to ventilate the room for a coupleof hours.The glass panel may require cleaning after the unithas cooled down. DO NOT ATTEMPT TO CLEANTHE GLASS WHILE IT IS HOT.Note: When the glass is cold and the applianceis lit, it may cause condensation and fogthe glass. This condensation is normaland will disappear in a few minutes asthe glass heats up.DO NOT BURN THE APPLIANCEWITHOUT THE GLASS FRONT INPLACE.During the first few fires, a white filmmay develop on the glass front as partof the curing process. The glass shouldbe cleaned or the film will bake on andbecome very difficult to remove. Use anon-abrasive cleaner and NEVER cleanthe glass while it is hot.OPERATINGINSTRUCTIONS1) Read and understand these instructionsbefore operating this appliance.2) Check to see that all wiring is correct andenclosed to prevent possible shock.3) Check to ensure there are no gas leaks.4) Make sure the glass in the door frame isproperly positioned. Never operate theappliance with the glass removed.5) Verify that the venting and cap areunobstructed.6) Ensure that the brick panels, if used, areinstalled.7) Verify log placement. If the pilot cannot beseen when lighting the unit, the logs havebeen incorrectly positioned.8) The unit should never be turned off, and onagain without a minimum of a 60 second wait.9) Hook up remote receiver to wire marked'receiver' which will be located on the bottomof the appliance. This remote control requirescoding. See remote control instructions fordetails.NOTE: This appliance will operate during poweroutages. Only the fan will not operate untilpower is restored. If the remote batteries inboth the handheld transmitter or receiver losepower, the appliance can still be operated bysliding the switch on the receiver switch from"Remote" to "ON". To turn on the applianceoff slide the receiver switch from "ON" to"Remote" or "OFF".IMPORTANT: The remote control system sup-plied with this appliance has several optionsfor starting/operating the appliance, pleaseread the remote control operating instructions(packed with remote control) to understandhow to operate this remote system. Optionto download remote functions video with QRcode below.ProflamevideoLIGHTINGPROCEDUREImportant: If the pilot does not hold, turn pilot knobto "OFF" position. Wait 5 minutes to clear gas. Ifyou smell gas - STOP! Follow the safety informationabove. If you don't smell gas, repeat Steps 1-6.1. Push in gas control knob slightly and turn to"PILOT" position.2. Push in control knob all the way and hold inuntil the pilot lights up. Continue to hold thecontrol knob in for about 20 seconds after thepilot is lit. Release knob.3. Push in gas control knob slightly and turn to"ON" position.4. Ensure the receiver is in the remote position.IMPORTANTPrior to igniting or re ignitingthe pilot, remove the glassdoor.Set Switch toRemoteDiagram 15. Press and release the ON/OFF button on theremote handheld transmitter. An audible beepshould be heard from the receiver.ON/OFFButtonDiagram 2Remote shown in Manual Mode on HiSHUTDOWNPROCEDURE1. Press "OFF" on the remote or slide receiverswitch from remote to "OFF".2. Turn the gas control knob to the "OFF" positionto turn off the pilot.Pilot may be shut off during prolonged non useperiods to conserve fuel.6. The unit will turn on.