Regency P33-LP10 Owners & Installation Manual

Regency P33-LP10 Owners & Installation Manual Manual pdf 9 page image

Regency ® P33-10 Zero Clearance Direct Vent Gas Fireplace | 9|9installationDUCT SYSTEM OPTIONKit #946-556The HeatWave Air Duct Kit increases theeffectiveness of your fireplace by dispersing warmair from the fireplace to remote locations in thesame room or other rooms in your home.Up to two kits may be installed on the fireplace.Please Note: Only 1 HeatWave kit may be oper-ated at one time. This includes the internal bloweroption as well.INSTALLATIONCHECKLIST1) Locate appliancea) Room location(Refer to "Locating Your Fireplace"Section)b) Clearances to Combustibles(Refer to "Clearances" Section)c) Mantle Clearances(Refer to "Combustible Mantels"Section)d) Framing & Finishing Requirements(Refer to "Framing & Finishing"Section)e) Venting Requirements(Refer to "Venting" Sections)2) Assemble Top Facing Support and SideNailing Strips (Refer to "Unit Assembly Priorto Installation" Section). NOTE: Must bedone before installing unit into fireplace.3) Install vent (Refer to "Venting" Sections).4) Install 4-AA batteries into receiver. This willenable operation of appliance manuallywhen in "ON" position.5) Make gas and electrical connections. Testthe pilot. Must be as per diagram.(Refer to "Gas Line Installation" and "PilotAdjustment" Section).Convert to Propane if desired.(Refer to "Conversion Kit from NG to LP"Section).6) Install standard and optional features. Referto the following sections:a. Optional Brick Panelsb. Log Set Installationc. Standard Glass Doord. Vignette Faceplatee. Optional Wall Thermostatf. Installing the Optional Fan7) Final check.Before leaving this unit with the customer,the installer must ensure that the appliance isfiring correctly and operation fully explainedto customer.This includes:1) Clocking the appliance to ensure the correctfiring rate (rate noted on label) after burningappliance for 15 minutes.2) If required, adjusting the primary air to ensurethat the flame does not carbon. First allowthe unit to burn for 15-20 min. to stabilize.CAUTION: Any alteration to the product thatcauses sooting or carboning that resultsin damage is not the responsibility of themanufacturer.Diagram 1LOCATING YOURFIREPLACE1) When selecting a location for your fireplace,ensure that the clearances outlined on thispage are met.2) P r o v i d e a d e q u a t e c l e a r a n c e s f o rservicing.3) The appliance must be installed on a flat,solid, continuous surface (e.g. wood, metal,concrete). This may be the floor, or raised upon a platform to enhance its visual impact.If the appliance is going to be installedon carpeting, combustible linoleum tile orother combustible material other than woodflooring, the appliance must be installed on ametal or wood panel extending the full widthand depth of the appliance.4) The P33-10 can be installed in a recessedposition or framed out into the room as inA, B, C, D. See Diagram 1 below.5) This appliance is Listed for bedroominstallations when used with a Listed MillivoltThermostat. Some areas may have furtherrequirements, check local codes beforeinstallation.6) The P33-10 Direct Vent Gas Fireplace isapproved for alcove installations, which meetthe clearances listed on the "Clearances"Section.7) We recommend that you plan your installationon paper using exact measurements forclearances and floor protection beforeactually installing this appliance. Have aqualified inspector, dealer, or installer reviewyour plans before installation.Note: For vent terminations see "Exterior VentTermination Locations" Section.A) Flat on WallB) Flat on Wall CornerC) Recessed into Wall/AlcoveD) CornerMANUFACTUREDMOBILE HOMEADDITIONALREQUIREMENTS1) Ensure that structural members are not cut orweakened during installation.2) Ensure proper grounding using the #8 groundlug provided. Refer to "Wiring Diagram" Section.