Saeco CAP001/A Instruction And Maintenance Manual

Contents

English116.7 Light coffee dispensingThis type of dispensing is performed by utilising doses of pre-groundcoffee manually introduced into the machine through the pre-groundcoffee slot (ref. 6, fig. 1). To the quantity thus provided manuallythe machine autonomously adds a small dose of ground coffee;this procedure compensates for the lesser quantity of ground cof-fee present in the pre-packaged bags and improves the organolepticqualities of the drink dispensed.- Briefly press (less than 1 sec.), the key twice and consecu-tively, the display will show “LIGHT COFFEE”;- introduce through the pre-ground coffee slot (ref. 6, fig. 1), thecontents of one dose of pre-ground coffee;- press key or .N.B.: Dispensing with pre-ground coffee is programmable onlyfor one dose.6.8 Dispensing coffee in jugThis function allows the dispensing of more coffees (programma-ble) in a single container (such as a jug).By pressing key 1 to 8 times, as many consecutive dispensinginstances as requested, up to a maximum of 2,5 litres of coffee.- Position the jug under the dispenser (ref. 21, fig. 1).- Briefly press (less than 1 sec.) key for as many times asthe number of instances to be dispensed.The display will show “JUG X …” with the number of pro-grammed dispensing instances;- press key to confirm and start the cycle;- the machine will supply the dispensing instances programmedand the display will show the icon of a jug being filled with thenumber of instances already dispensed.- having completed the dispensing, the display will show again“READY FOR USE”;- if the cycle has to be stopped before the preset time it will besufficient to either press the jug key or any coffee keys.N.B.: Once the desired quantity has been set, it must be con-firmed by pressing the button within 10 seconds, otherwisedata are not saved.N.B.: The electronic control of the machine automatically man-ages the double coffee dispensing cycle to reduce to the minimumthe time taken.Example: by programming 5 dispensing instances, the electroniccontrol will set up dispensing for 2 double coffees plus a single one.N.B.: Warning: after 1 jug dispensing at full dosage (approx. 2litres) it is necessary to pause for 2 minutes to allow the machinestandard conditions restoration.6.9 Hot water dispenser (LUXE version)This function allows multiple (programmable) dispensing of hot waterin a single container.By pressing 1 to 8 times key as many consecutive and contin-uous dispensing instances will be obtained, up to a maximum of 1litre of hot water in the same container.- Position the container under spout (ref. 11, fig. 1).- Briefly press (less than 1 sec.), multiple times, key accord-ing to the number of desired dispensing instances.The display will show “HOT WATER X …” with the numberof programmed dispensing instances;- press key to confirm and start the cycle;- the machine will supply the dispensing instances programmedand the display will show the icon of a container being filledwith the number of instances already dispensed.- having completed the dispensing, the display will show again“READY FOR USE”;N.B.: Once the desired quantity has been set, it must be con-firmed by pressing the button within 10 seconds, otherwisedata are not saved.N.B.: It is possible to dispense a programmed dose of hot wateronly when function “HOT WATER PROGRAMM.” is in “ON”mode (see “6.14 Menu-programmable functions”);If instead the function is “OFF”, the dispensing must be stoppedby pressing again key .Danger of burnsNever direct the hot water jet towards body parts. Direct thepipe only by moving it through the special rubber heat pro-tector (ref. 9, fig. 1).It is furthermore advisable to keep the spout submerged withinthe container.6.10 Steam dispenser (LUXE version)Submerge the spout (ref.16, fig. 1) within the liquid to be warmedup and rotate the knob (ref. 12, fig. 1) anti-clockwise.After having reached the desired temperature close the knob againby rotating it clockwise.Danger of burnsNever aim the steam jet towards body parts. Direct the pipe onlyby moving it through its rubber heat protector (ref. 14, fig. 1).It is advisable to keep the spout submerged within the container.ImportantAfter each usage always clean the traces of the heated drinkfrom the spout with a moist cloth.