Saeco CAP001/A Instruction And Maintenance Manual

Contents

English17ON/OFF TIMEThis function allows the programming of the machine’s automaticswitch-on/off times for the whole of a weekly time span.- By confirming “ ON/OFF TIME”, the cursor will be posi-tioned on the day to be modified.- Program the day with key (down), thus shifting the letterfrom upper to lower case.- Remove the day from program, with key (up), shifting letterfrom upper to lower case.- Confirm the modification.To modify the timetable follow the same procedure used for thesetting of the clock.Example: The functions flow chart details a program whereby themachine is started at 08:00 and stopped at 18:00 Monday toFriday; from 09:00 to 12:30 on Saturday and a complete pauseon Sunday.COUNTERSThese are two functions that represent respectively the total numberof coffee dispensing cycles and the total number of hot waterdispensing cycles.When the automatic hot water dosing is disabled (see function“HOT WATER PROGRAMM.”), a cycle will be counted foreach command to the solenoid valve.N.B.: Both functions are read-only and they cannot be reset.ANTIFREEZINGThe anti-freeze function protects the machine from possible dam-age caused by exposure to low temperatures, in “STANDBY”status, causing the formation of ice in the boilers. This functionmaintains the boiler temperature at a minimum value that avoidsfreezing.- By confirming “ON”, the function is enabled.- By confirming “OFF”, it is disabled.N.B.: the function is activated only if function “AUTOMATICOPERATION” is also activated and at the same time the ma-chine is in “STANDBY”. When the function is activated the dis-play shows “ANTIFREEZING”.UNBLOCKINGThis function allows the temporary release of the machine, when ithas reached the number of programmed cycles for maintenanceor descaling. To obtain the releasing code, the user must contactthe firm that was responsible for installation or was appointed tosupply maintenance service. Having obtained the code, it must beinserted in the function:- Confirm function “UNBLOCKING”, the cursor is positionedunder the first digit to be modified;- insert the value and confirm;- after each confirmation the cursor is positioned under the nextdigit and so on, until the whole code is complete.6.15 Machine switching offAutomatic programmed switching offIt is possible when the function “AUTOMATIC OPERATION”(see “6.14.2 Functions description”) is active and the program-ming of “ON/OFF TIME” (see 6.14.2 Functions description)has also been carried out.At the programmed time the machine is set on “STANDBY”.Manual switching offThis type of switching off is necessary when function “AUTO-MATIC OPERATION” (see “6.14.2 Functions description”) isnot activated.It is obtained by setting both the main switch (ref. 10, fig. 1) andthe multi-pole switch to position “O” or disconnecting the plug.6.16 Disassembling/assemblingthe cover panels“CAUTION: To Reduce the Risk of Electric shock or MechanicalInjury, Do Not Remove This Cover. No User Serviceable PartsInside. Repair and Cleaning Should Be Done By Authorised Serv-ice Personnel Only (Only for USA and CDN models).”The side panels (ref. 1 and 5, fig. 11) and the back panel (ref. 3,fig. 11) can be dismantled for servicing or for customization thatmay suit room furniture or wall painting.DangerOperation falling within the competence of the Maintenancetechnician.Disconnect the machine from mains by way of main switch (ref.10, fig. 1) and all-pole switch, or disconnecting the plug.Danger of burnsWait for the machine to cool off sufficiently, before servicingit.For parts removal, do the following:- Pull out the drip tray (ref. 15, fig. 11).- Manually rotate the studs (ref. A, fig. 11) by 1/4 of a turnwith a 4 mm hexagonal spanner and slide side panels (ref. 1and 5, fig. 11) upwards.- Slide glass out (ref. 2, fig. 11).- Dismantle the cup heating plate (ref. 4, fig. 11) by disconnect-ing it from the electronic board, from the earth cable and fromthe drain tube (ref. B, fig. 11).- Unscrew the back panel retaining nuts (ref. 3, fig. 11) anddismantle it.To re-assemble one must:- Assemble the back panel (ref. 3, fig. 11) and secure it with therelative nuts.