Saeco Modular Coffee Instruction And Maintenance Manual

Also see for Modular Coffee: Instruction and maintenance manual

Contents

EnglishON/OFF TIMEThis function allows the programming of the machine'sautomatic switch-on/off times for the whole of a weekly timespan.- By confirming " ON/OFF TIME", the cursor will be posi-tioned on the day to be modified.- Program the day with key (down), thus shifting theletter from upper to lower case.- Remove the day from program, with key (up), shiftingletter from upper to lower case.- Confirm the modification.To modify the timetable follow the same procedure used forthe setting of the clock.Example: The functions flow chart details a programwhereby the machine is started at 08:00 and stopped at 18:00 Monday to Friday; from 09:00 to 12:30 on Saturday anda complete pause on Sunday.6.15 Machine switching offAutomatic programmed switching offIt is possible when the function "AUTOMATIC OPERATION"(see "6.14.2 Functions description") is active and theprogramming of "ON/OFF TIME" (see 6.14.2 Functionsdescription) has also been carried out. At the programmedtime the machine is set on "STANDBY"Manual switching offThis type of switching off is necessary when function "AUTO-MATIC OPERATION" (see "6.14.2 Functions description")is not activated.It is obtained by setting both the main switch (ref. 10, fig. 1)and the multi-pole switch to position "O" or disconnecting theplug.COUNTERSThese are two functions that represent respectively the totalnumber of coffee dispensing cycles and the total number ofhot water dispensing cycles.When the automatic hot water dosing is disabled (seefunction "HOT WATER PROGRAMM."), a cycle will becounted for each command to the solenoid valve.N.B.: Both functions are read-only and they cannot be reset.ANTIFREEZINGThe anfi-freeze function protects the machine from possibledamage caused by exposure to low temperatures, in"STANDBY" status, causing the formation of ice in theboilers. This function maintains the boiler temperature at aminimum value that avoids freezing.- By confirming "ON", the function is enabled.- By confirming "OFF", it is disabled.N.B.: the function is activated only if function "AUTOMATICOPERATION" is also activated and at the same time the ma-chine Is in "STANDBY" When the function Is activated thedisplay shows "ANTIFREEZING".6.16 Disassembling/assemblingthe cover panels"CAUTION: To Reduce the Risk of Electric shock orMechanical Injury, Do Not Remove This Cover. No UserServiceable Parts Inside. Repair and Cleaning Should BeDone By Authorized Service Personnel Only (Only for USAand CDN models)."The side panels (ref. 1 and 5, fig. 11) and the back panel (ref.3, fig. 11) can be dismantled for servicing or for customizationthat may suit room furniture or wall painting.DangerOperation falling within the competence of theMaintenance technician.Disconnect the machine from mains by way of main switch(ref. 10, fig. 1) and all-pole switch, or disconnecting the plug.Danger of burnsWaif for the machine to cool off sufficiently, beforeservicing it.UNBLOCKINGThis function allows the temporary re ease of the machine,when it has reached the number of programmed cycles formaintenance or descaling. To obtain the releasing code, theuser must contact the firm that was responsible forinstallation or was appointed to supply maintenance service.Having obtained the code, if must be inserted in the function:- Confirm function "UNBLOCKING", the cursor ispositioned under the first digit to be modified;- insert the value and confirm;- after each confirmation the cursor is positioned under thenext digit and so on, until the whole code is complete.For parts removal, do the following:- Pull out the drip tray (ref. 15, fig. 11).- Manually rotate the studs (ref. A, fig. 1 1) by 1/4 of a turnwith a 4 mm hexagonal spanner and slide side panels(ref. 1 and 5, fig. 1 1) upwards.- Slide g ass out (ref. 2, fig. 1 1).- Dismantle the cup heating plate (ref. 4, fig. 11) bydisconnecting it from the electronic board, from the earthcable and from the drain tube (ref. B, fig. 1 1).- Unscrew the back pane retaining nuts (ref. 3, fig. 1 1) anddismantle it.To re-assemble one must:- Assemble the back panel (ref. 3, fig. 1 1) and secure ifwith the relative nuts.17