Sanyo PLC-XD2200 Service Manual

Also see for PLC-XD2200: Owner's manual Easy setup Manual Manual Command list

Contents

-50-Electrical AdjustmentsGroup/Item Item Name Function Initial range Note4 Cr Imange Area Start X Cr Acquiring Area H-Start Position 500 0-10005 Cr Imange Area Start Y Cr Acquiring Area V-Start Position 200 0-10006 Image Area H Width Image Level Acquiring Area 8 0-40957 Image Area V Hight Image Level Acquiring Area Height 9 0-40958 Y Target Level Target Value of Y Level Adj. 217 0-2559 Cb Target Level Target Value of Cb Level Adj. 212 0-25510 Cr Target Level Target Value of Cr Level Adj. 212 0-25511 Gain Tolerance Torelance of Level Adj. 1 0-25512 Delta Gain Deviation Width of Gain Value 9 0-255Group264 Auto calibration (Ycbcr)0 Y-OFFSET AREA H START Y - Offset Acquiring Area H-StartPosition 925 0 - 10001 Y-OFFSET AREA V START Y - Offset Acquiring Area V-StartPosition 500 0 - 10002 CB - OFFSET AREA HSTART CB - Offset Acquiring Area H-StartPosition 925 0 - 1000 CB - OFFSET AREA V START CB - Offset Acquiring Area V-StartPosition 500 0 - 10004 CR - OFFSET AREA HSTART CR - Offset Acquiring Area H-StartPosition 925 0 - 10005 CR - OFFSET AREA V START CR - Offset Acquiring Area V-StartPosition 500 0 - 10006 Y - GAIN AREA H START 50 0 - 10007 Y - GAIN AREA V START 500 0 - 10008 CB - GAIN AREA H START 800 0 - 10009 CB - GAIN AREA V START 500 0 - 100010 CR - GAIN AREA H START 700 0 - 100011 CR - GAIN AREA V START 500 0 - 100012 Image AREA H WIDTH YCBCR Level Acquiring Area 1 0 - 40951 Image AREA V HIGHT YCBCR Level Acquiring Area Height 9 0 - 409514 Y - OFFSET TARTGET 4 0 - 25515 CB OFFSET TARGET 128 0 - 25516 CR OFFSET TARGET 128 0-25517 Y-GAIN TARGET 217 0-25518 CB-GAINTARGET 27 0-25519 CR-GAINTARGET 27 0-25520 OFFSET torelance Torelance of OFFSET Adj. 1 1-25521 GAIN torelance Torelance of GAIN Adj. 1 1-255Group270 cuStoM(Aspect)0 Scaler Horizontal Horizontal Scaler Edit 100 68-121 Sclaler Vertical Vertical Scaler Edit 100 68-122 Connect Seperate/Connect Edit 0 0-1 0:Seperate, 1: Connect Position Horizontal Horizontal Postion Correction 100 85-1154 Position Vertical Vertical Position Correct 100 85-1155 Aspect Enable Aspect Adj. Enable 0 0-1 1: Enable, 0: DisableGroup280 AutoPc Adjust0 AutoPCAdjustEnable Auto-PC Adj Operation Enable if Un-supported Signal Input 0 0-1 0:Enabel, 1:Disable1 Frequency Step Frequency Steps of Total Dot 1 0-2 Frequency Threshold Total Dot Freqency Threshold 5 0-10 0[]<-- - --> 10[Not matched] Fine Phase Do Phase Adj after Total Dot Adj. 1 0-1 0;Excutes Fine Phase; 1:Not Excute4 BLKDET Black Level Detection Area 1 0 - 5 PHASEMSK Phase Detection Filter 0 0 - 0: Effective All Bit,1: Disable Lower 1 bit2: Disable Lower 2 bit, : DisableLower bitGroup290 Paneltype * Panel type check0 GammaL/R-View Current Setting Check 0 0-20 0: Gamma for L-Turn20: Gamma for R-Turn * Read only1 GammaL/R-Change Setting of Gamma 10 0-20Sets L-Turn Gamma if the Value isset to 0.Sets R-Turn Gamma if the Value isset to 20.Group500 composite (NtSc) composite / S-Video0