Ubiquiti AirFiber 11FX User Manual

Also see for airFiber 11FX: Quick start guide

18Chapter 4: DashboardairFiber AF-11FX User G uideUbiquiti Networks, Inc.Signal StrengthThe Signal Strength section displays signal strength,capacity, and speed information.LocalSignal Strength Displays the signal strength for Chain 0and Chain 1.Ideal Power Displays the ideal power level of the receivedsignal.Chain Imbalance Displays the difference between theactual and ideal power levels.Local RX Real-Time Capacity/Speed Charts for Capacity(orange) and Throughput (blue) display the potential andcurrent RX data traffic.Modulation Rate Displays the current modulation rate:MIMO SISO10x (1024QAM) 5x (1024QAM)8x (256QAM) 4x (256QAM)6x (64QAM) 3x (64QAM)4x (16QAM) 2x (16QAM)2x (QPSK) 1x (QPSK)1x (QPSK) 1/4x (QPSK)1/4x (QPSK) –If Automatic Rate Adaptation is enabled on the Wireless tab,then Modulation Rate displays the current speed in useand depends on the Maximum Modulation Rate specifiedon the Wireless tab and current link conditions.RemoteSignal Strength Displays the signal strength for Chain 0and Chain 1.Ideal Power Displays the ideal power level of the receivedsignal.Chain Imbalance Displays the difference between theactual and ideal power levels .Remote RX Real-Time Capacity/Speed Charts forCapacity (orange) and Throughput (blue) display thepotential and current RX data traffic.Modulation Rate Displays the current modulation rate(see Modulation Rate description in the Local sectionabove).If Automatic Rate Adaptation is enabled on the Wireless tab,then Modulation Rate displays the current speed in useand depends on the Maximum Modulation Rate specifiedon the Wireless tab and current link conditions.DeviceOperating Mode Displays the mode of the airFiber Xradio: Slave, Master, or Reset.RF Link Status Displays the status of the airFiber X radio:RF Off, Syncing, Beaconing, Registering, Enabling, Listening,Operational, DFS CAC, or RADAR Detected.Note: Most RF Link Status values map to specificflash rates of the Link Status LED (See “LEDs” onpage 2 for more details.)Status Flash Rate of LEDRF Off OffBeaconing Normal Flash (1:1 on/off cycle)Registering Long Flash (3:1 on/off cycle)Operational OnVersion Displays the airFiber Configuration Interfacesoftware version.Date Displays the current system date and time. Thedate and time are displayed in YEAR-MONTH-DAYHOURS:MINUTES:SECONDS format. The system date andtime is retrieved from the Internet using NTP (NetworkTime Protocol). The NTP Client is enabled by default onthe Services tab. The airFiber X radio has no internal clock,and the date and time may be inaccurate if the NTP Clientis disabled or the device is not connected to the Internet.Radio Mode Displays the radio mode: MIMO or SISO.Uptime This is the total time the device has been runningsince the latest reboot (when the device was powered up)or software upgrade. The time is displayed in days, hours,minutes, and seconds.Link Uptime This is the total time the airFiber link hasbeen continuously operational. The time is displayed indays, hours, minutes, and seconds.Regulatory Domain Displays the regulatory domain(FCC/IC, ETSI, or Other), as determined by countryselection.Security AES-128 is enabled at all times.Conducted TX Power Displays the conducted transmitpower out of the radio before any antenna gain.Net Gain Displays the airFiber X radio’s net antenna gain,which is the antenna gain minus cable loss. Antennagain (the gain of the antenna being used) and cable loss(the loss in the cable from the radio to the antenna) areset using the Antenna Gain and Cable Loss fields on theWireless tab.