Wascomat WS3 230-340-470-670 H Instruction Handbook Manual

Notice Date Page01201055INSTRUCTIONHANDBOOK0102 8 88.TechnicalcharacteristicsHeating Gas Electric Steam Thermic fluidCharacteristics Ø cage --------------------------- 770 mm (30.31")--------------------Cage length ----------------------------- 1500 mm (59") -------------------Cage volume ----------------------- 668 dm³ (668 l) --------------------Specific load 1/11 --------------------------- 61 kg (134 lb)-----------------------(dry linen, ISO 9398-4)Opening cage doors (L x H) ---------------- 2x600 x 400 mm (23.62x15.74")-----------Opening drum door (L x H) --------------- 2x616 x 525 mm (24.25x20.66") -----------Floor area ------------------------ 2 m² (21.53 sq. ft) --------------------Net weight --------------------------- 940 daN (2073 lb)-----------------Weight loaded (high level) ---------------------------1589 daN (3504 lb)-----------------Water, washing, low level xx l xx l xx l xx lWater, washing, high level xx l xx l xx l xx lDynamic stress --------------------- F = 466 daN (1028 lb)-------------------Transmitted floor load ------------------------ 811 daN (1789 lb)------------------Spin efficiency ---------------------------------- 350 G ------------------------Max. unbalance --------------------------- 8 kg (17.65 lb)--------------------(L) Main switch to connect main cable(M) Electric cable (section) 4x2.5 mm² 4x35 mm² 4x2.5 mm² 4x2.5 mm²(N) or (N') Stuffing box for main cableSupply voltage -------------------------380 / 415 V 3+E ~ 50/60 Hz------------Installed electric power 7.8 kW 61.5 kW 7.8 kW 7.8 kWInstalled heating power 40 kW 54 kW - -Electrical consumption for a normal cycle* 2 kWh/h 23 kWh/h 2 kWh/h 2 kWh/hHeat loss -------------------3 % of installed heating power--------------(G) Steam inlet DN 20 (3/4" BSP)- Maximum supply pressure 600 kPa (87 psi)- Steam instantaneous flow rate at 600 kPa x kg/h- Steam consumption for a normal cycle* 24.5 kg/h at 600 kPa (87 psi)(D) Hot water connection / flow DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)(E) Cold hard water connection / flow DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)(F) Cold soft water connection / flow (option) DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)Water supply minimum pressure --------------------------- 50 kPa (7.25 psi)------------------Water supply maximum pressure --------------------------- 300 kPa (43.5 psi)----------------Water consumption for a normal cycle* 977 l 977 l 977 l 977 lWater consumption for an ECO cycle** 782 l 782 l 782 l 782 l(K) Liquid detergents inlet(H1 or H3 or H5) Drain connection --------------------------- Ø 75 mm (3")----------------------(H2 or H4 or H6) Double drain connection --------------------------- Ø 75 mm (3")----------------------Maximum drain flow rate xx l/min xx l/min xx l/min xx l/min(I) Waste water collector ------------------------ DN 150 mm (6" BSP)----------------(3 cm/m (3 %) minimum slope)(J) Air vent hole ------------------------ Ø 60 mm (2.36 ") ---------------------(N') Thermic fluid inlet DN 15 (1/2" BSP)(G) Thermic fluid return DN 15 (1/2" BSP)- Maximum supply pressure xxx kPa- Installed calorific power xxx kcal- Average calorific consumption xxx kcal/h- Inner volume thermic fluid xx lGas inlet DN 20 (3/4" BSP)Combustion products evacuation Ø 125 mm (5")Washer extractor type 670 standard Diagram no. 07100087* normal cycle : prewash 3 min at 35 °C, drain. 2 min, main wash 4 min at 65 °C, drain 2 min, rinse 2 min, extract. 2 min, rinse 2 min,extract 2 min, rinse 2 min, extrac. 10 min (cold water supply at 15 °C).** ECO cycle : normal cycle with rinse 5 l/kg instead of 6 l/kg dry linen.