Wascomat WS3 230-340-470-670 H Instruction Handbook Manual

Notice Date Page01201055INSTRUCTIONHANDBOOKWasher extractor type 230 barrier Diagram no. 071000820102 10 88.TechnicalcharacteristicsHeating Gas Electric Steam Thermic fluidCharacteristics Ø cage --------------------- 770 mm (30.31") -------------------Cage length --------------------- 520 mm (20.47") -------------------Cage volume ---------------------- 229 dm³ (229 l) ---------------------Specific load 1/11 -------------------- 21 kg (46 lb) -------------------(dry linen, ISO 9398-4)Opening cage doors (L x H) ----------- 450 x 400 mm (17.71x15.74") -------------Opening drum door (L x H) ----------- 466 x 525 mm (18.34x20.67") -------------Floor area ------------------- 1 m² (10.76 sq. ft) -------------------Net weight --------------------- 670 daN (1478 lb) -------------------Weight loaded (high level) --------------------- 934 daN (1840 lb) -------------------Water, washing, low level xx l xx l xx l xx lWater, washing, high level xx l xx l xx l xx lDynamic stress ---------------------- F = 101 daN (222 lb) --------------------Transmitted floor load ----------------------- 814 daN (1795 lb) ----------------------Spin efficiency ------------------------------- 350 G -------------------------------Max. unbalance ----------------------------- 3.6 kg (7.94 lb) ---------------------(L) Main switch to connect main cable(M) Electric cable (section) 4x2.5 mm² 4x6 mm² 4x2.5 mm² 4x2.5 mm²(N) or (N') Stuffing box for main cableSupply voltage -------------------------380 / 415 V 3+E ~ 50/60 Hz------------Installed electric power 3.7 kW 21.70 kW 3.7 kW 3.7 kWInstalled heating power 40 kW 18 kW - -Electrical consumption for a normal cycle* 0.8 kWh/h 5.3 kWh/h 0.6 kWh/h 0.6 kWh/hHeat loss -------------------3 % of installed heating power--------------(G) Steam inlet DN 20 (3/4" BSP) (87 psi)- Maximum supply pressure 600 kPa- Steam instantaneous flow rate at 600 kPa x kg/h- Steam consumption for a a normal cycle* 12 kg/h at 600 kPa (87 psi)(D) Hot water connection / flow DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)(E) Cold hard water connection / flow DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)(F) Cold soft water connection / flow (option) DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)Water supply minimum pressure ---------------------- 50 kPa (7.25 psi) -------------------Water supply maximum pressure ---------------------- 300 kPa (43.5 psi) ------------------Water consumption for a normal cycle* 360 l 340 l 340 l 340 lWater consumption for an ECO cycle** 282 l 260 l 260 l 260 l(K) Liquid detergents inlet(H1 or H3 or H5) Drain connection ------------------------- Ø 75 mm (3") ---------------------(H2 or H4 or H6) Double drain connection ------------------------- Ø 75 mm (3") ---------------------Maximum drain flow rate xx l/min xx l/min xx l/min xx l/min(I) Waste water collector --------------------- DN 150 mm (6" BSP) --------------(3 cm/m (3 %) minimum slope)(J) Air vent hole ------------------------ Ø 60 mm (2.36") ------------------(N') Thermic fluid inletDN 15 (1/2" BSP)(G) Thermic fluid return DN 15 (1/2" BSP)- Maximum supply pressure xxx kPa- Installed calorific power xxx kcal- Average calorific consumption xxx kcal/h- Inner volume thermic fluid xx lGas inlet DN 20 (3/4" BSP)Combustion products evacuation Ø 125 mm (5")(O) Barrier partition (provided by customer)(P) Frame 50x100 mm (provided by customer)(R) Foam joint* normal cycle : prewash 3 min at 35 °C, drain. 2 min, main wash 4 min at 65 °C, drain 2 min, rinse 2 min, extract. 2 min, rinse 2 min,extract 2 min, rinse 2 min, extrac. 10 min (cold water supply at 15 °C).** ECO cycle : normal cycle with rinse 5 l/kg instead of 6 l/kg dry linen.