YASKAWA A1000 HHP Programming Manual

Contents

Fault Reset Methods............................................................ 179Fault Reset Operation Selection ........................................ 148, 286Fault Restart ..................................................................... 113Faults ............................................................................. 179Fault SlaveLocation Monitor.................................................. 301Fault Trace................................................................. 171, 224FbH ......................................................................... 189, 206FbL ......................................................................... 189, 206Field Forcing ......................................................................72Field Forcing Limit ...............................................................73Field Forcing Selection ..........................................................72Field Weakening ..................................................................72Field Weakening Frequency Limit .............................................72Field Weakening Level ..........................................................72Fine-Tuning Open Loop Vector Control .................................... 176Fine-Tuning V/f Control and V/f Control with PG ........................ 176FJOG/RJOG Operation ..........................................................99Forward/Reverse Run Command Input Error............................... 205Forward Regenerative Torque Limit ................................... 151, 287Forward Torque Limit.................................................... 151, 287Frequency Detection 1 Time Chart........................................... 108Frequency Detection 2 Time Chart........................................... 108Frequency Detection 3 Example with a Positive L3-04 Value ........... 111Frequency Detection 4 Example with Positive L3-04 Value ............. 112Frequency Reduction Rate during Overheat Pre-Alarm............. 153, 289Frequency Reference .......................................................59, 298Frequency Reference at Previous Fault ...................................... 300Frequency Reference at Reference Loss............................... 146, 285Frequency Reference Bias .......................................................65Frequency Reference Bias (Up/Down 2) .................................... 306Frequency Reference Bias Accel/Decel .......................................66Frequency Reference Bias Lower Limit .......................................65Frequency Reference Bias Operation Mode Selection ......................66Frequency Reference Bias Step.................................................65Frequency Reference Bias Upper Limit .......................................65Frequency Reference from MEMOBUS/Modbus Comm. ................ 303Frequency Reference Hold Function Selection ...............................63Frequency Reference Loss Detection Selection ...................... 109, 285Frequency Reference Lower Limit .............................................61Frequency Reference Monitor Content During PID .........................42Frequency Reference Selection ............................................... 240Frequency Reference Selection 1.........................................18, 227Frequency Reference Selection 2...............................................24Frequency Reference Setting / Decimal Display ........................... 292Frequency Reference Setting and User-Set Display ....................... 292Frequency Reference Setting Hierarchy .......................................59Frequency Reference Setting Method Selection...................... 163, 293Frequency Reference Source Selection ...................................... 303Frequency Reference Upper Limit .............................................61Function Code................................................................... 324Functions for Terminals S1 to S8...............................................95Fuse is Open ..................................................................... 198GGate Drive Board Undervoltage .............................................. 201GF................................................................................. 189Ground Fault .................................................................... 189HH1 Multi-Function Digital Input Selections................................. 269H3-02 ............................................................................. 230H3-13 ............................................................................. 177H3 Multi-Function Analog Input Settings................................... 277Hbb ............................................................................... 206HbbF.............................................................................. 207HCA .............................................................................. 207HD ..................................................................................58Heatsink Cooling Fan Off-Delay Time ...................................... 155Heatsink Cooling Fan Operation Delay Time .............................. 288Heatsink Cooling Fan Operation Selection............................ 154, 288Heatsink Overheat ........................................................ 193, 208Heatsink Overheat Warning ................................................... 208Heatsink Temperature.......................................................... 302Heavy Duty ........................................................................58High Current Alarm Selection ................................................ 156High Slip Braking .............................................................. 159High Slip Suppression Current Level ........................................ 160High-Slip Suppression Current Level........................................ 291Hunting Prevention ............................................................. 158Hunting Prevention Gain ...................................................... 176Hunting Prevention Gain Setting ....................................... 158, 290Hunting Prevention Gain while in Reverse ........................... 158, 290Hunting Prevention Selection ........................................... 158, 290Hunting Prevention Time Constant .................................... 158, 290HVAC Fan Application ..........................................................15Hybrid IC Failure ............................................................... 186IiFEr ............................................................................... 222IGBT Maintenance ............................................................. 302IGBT Maintenance Setting .............................................. 166, 293IGBT Maintenance Time (50%) .............................................. 208IGBT Maintenance Time (90%) ............................................. 211Induction Voltage Error........................................................ 220Initialization .......................................................................10Initialization Required ......................................................... 214Initialize Parameters..............................................................11Input Phase Loss ................................................................ 197Input Phase Loss Protection Selection ................................. 153, 288Input Pulse Monitor ............................................................ 300Input Terminal Status .......................................................... 298Input Terminal Status at Previous Fault ..................................... 301Input Voltage Setting.............................................................74Inrush Prevention Relay Fault ................................................ 201Inrush Prevention Relay Maintenance Setting .............................. 293Integral Limit Setting.............................................................37Integral Operation during Accel/Decel ........................................56Integral Operation during Accel/Decel for Motor 2..........................57Integral Time Setting (I) .........................................................37JJog Frequency Reference ........................................................59Jump Frequency................................................................. 177Jump Frequency Width ..........................................................62KKEB Acceleration Time ................................................. 140, 283KEB Detection Time ........................................................... 140KEB Function Related Adjustments ......................................... 139KEB Operation Using a KEB Input .......................................... 136KEB Operation Using L2-02, Without KEB Input......................... 136Index350 YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual