Danfoss H1 Series manuals
H1 Series
Table of contents
- Table Of Contents
- Table Of Contents
- Overview
- Safety Precautions
- Design
- Pump schematic
- The system circuit
- Pressure Limiter Valves (060/068 only)
- Charge Pressure Relief Valve
- Electrical displacement control (EDC)
- Manual OverRide (MOR)
- Manual Displacement Control (MDC)
- Control-Cut-Off (CCO) valve and brake valve
- Charge inlet pressure
- H1T general specifications
- Operating parameters H1 Tandem
- Fluid and filter recommendations
- Port locations and gauge installation - 045/053
- Port locations and gauge installation - 060/068
- General
- Neutral difficult or impossible to find
- System noise or vibration
- Pump adjustment
- Charge check / HPRV adjustment
- Engaging the Bypass Function (060/068 only)
- Displacement limiter adjustment
- Control Neutral Adjustment
- Mechanical neutral adjustment
- Pump setup
- Servo adjustment
- Standard procedures, removing the pump
- Control solenoids
- MDC illustration - tandems
- Angle sensor on EDC
- EDC with angle sensor
- Front Shaft, seal, and bearing
- Charge Pump (045/053 only)
- Assembly
- HPRV (60/68)
- Control cutoff valve and brake valve
- Fastener size and torque chart
- Fasteners and plugs
H1 Series
Table of contents
- Table Of Contents
- Table Of Contents
- H1 Pumps General Specification
- H1P 115/130 Operating Parameters
- Fluid Specifications
- H1P 115/130 Mounting Flange Loads
- Charge pump
- Electrical Displacement Control (EDC)
- EDC Solenoid Data
- Response Time, EDC 115/130
- Manual Displacement Control (MDC)
- MDC General Information
- Control Response
- Connector
- Forward-Neutral-Reverse Electric Control (FNR)
- Non Feedback Proportional Electric Control (NFPE)
- Automotive Control (AC)
- Performance functions
- Fan Drive Control (FDC)
- Manual Over Ride (MOR)
- Swash Plate Angle Sensor for EDC Controls
- Swash Plate Angle Sensor Connector
- Swash plate angle sensor for NFPE and AC2 controls
- Control-Cut-Off valve (CCO valve)
- CCO solenoid data
- H1P input shaft - Option G3 (SAE D, 13 teeth)
- H1P input shaft - Option G2 (SAE D, 27 teeth)
- H1P input shaft - Option F3, Code 44-3
- Tapered shaft customer acknowledgement
- H1P 115/130 Auxiliary mounting - Option H1 (SAE A, 11 teeth)
- H1P 115/130 Auxiliary mounting - Option H2 (SAE A, 9 teeth)
- H1P 115/130 Auxiliary mounting - Option H3 (SAE B, 13 teeth)
- H1P 115/130 Auxiliary mounting - Option H4 (SAE D, 13 teeth)
- H1P 115/130 Auxiliary mounting - Option H5 (SAE B-B, 15 teeth)
- H1P 115/130 Auxiliary mounting - Option H6 (SAE C, 14 teeth)
- H1P 115/130 Auxiliary mounting - Option S1 (SAE B-B, 14 teeth)
- H1P 115/130 displacement limiter, option B and D
- Port Description H1P115/130
- Dimensions H1P 115/130
- Electric Displacement Control (EDC), option A2 (12 V) / A3 (24 V)
- H1P 115/130 Manual Displacement Control (MDC), option M1
- H1P 115/130 Manual Displacement Control (MDC) with NSS, option M2
- H1P 115/130 Manual Displacement Control (MDC) with CCO, option M3, M4
- H1P 115/130 Manual Displacement Control (MDC) with NSS and CCO, option M5, M6
- Non Feedback Proportional Electric control (NFPE), with manual override, option A8 (12 V) / B8 (24 V)
- Automotive Control (AC) Dimensions
- Forward-Neutral-Reverse (FNR) with manual override, options A9 (12 V) / B1 (24 V)
- H1P 115/130 suction filtration, option L
- H1P 115/130 filtration, option M
Related products
Series 2051 SeriesMAH Series51-1 SeriesTMTHW SeriesL Frame SeriesFCM 300 SeriesK Frame SeriesEM-PME375 SeriesVLT AutomationDrive FC 300 SeriesDanfoss categories
Controller
Air Compressor
Heat Pump
Control Unit
DC Drives
Water Pump
Thermostat
Industrial Equipment
Media Converter
Switch
manualsdatabase
Your AI-powered manual search engine