Genie Lift Guard GR-15 manuals
Lift Guard GR-15
Table of contents
- Introduction
- November 2005
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Machine Specifications
- Performance Specifications
- Manifold Component Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Maintenance Inspection Report
- A-1 Perform Pre-operation Inspection
- A-3 Perform 30 Day Service
- B-1 Inspect the Batteries
- B-2 Inspect the Electrical Wiring
- B-3 Inspect the Tires and Wheels (including castle nut torque)
- B-5 Clean and Lubricate the Columns
- B-7 Test the Emergency Stop
- B-8 Test the Key Switch
- B-10 Inspect the Voltage Inverter (if equipped)
- B-11 Test the Drive Brakes
- B-12 Test the Drive Speed - Stowed Position
- B-13 Test the Drive Speed - Raised Position
- B-14 Test the Slow Drive Speed
- B-15 Test the Flashing Beacons
- B-17 Perform Hydraulic Oil Analysis
- B-18 Inspect the Breather Cap
- C-1 Grease the Platform Overload Mechanism (if equipped)
- C-3 Test the Platform Overload System (if equipped)
- D-1 Calibrate the Platform Overload System (if equipped)
- D-2 Inspect the Mast Assembly for Wear
- D-3 Inspect and Lubricate the Lifting Chains
- E-1 Test or Replace the Hydraulic Oil
- Circuit Boards
- Controller Adjustments
- Software Configuration
- Platform
- Mast
- Glide Pads
- Lift Cylinder
- Level Sensor
- Function Pump
- Function Manifold Components
- Valve Adjustments - Function Manifold
- Valve Coils
- Hydraulic Tank
- Yoke and Drive Motor
- Steer Cylinder
- Drive Brake
- Brake Release Hand Pump Components
Lift Guard GR-15
Table of contents
Lift Guard GR-15
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Specifications
- Performance Specifications
- Hydraulic Oil Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
- Section 3 Scheduled Maintenance Procedures
- Maintenance Schedule
- Pre-Delivery Preparation Report
- Scheduled and Programmed Maintenance Inspection Report
- Commissioning Procedures
- Quarterly Maintenance Procedures
- Q-2 Battery Inspection
- Q-3 Inspect the Electrical Wiring
- Q-5 Inspect the Voltage Inverter (if equipped)
- Q-6 Test the Flashing Beacons (if equipped)
- Q-8 Inspect the Tires and Wheels (including castle nut torque)
- Q-9 Check the Lifting Chain Adjustments
- Q-11 Adjust the Sequencing Cables
- Q-12 Visual Inspection of the Hydraulic Oil
- Q-13 Test the Drive Brakes
- Q-14 Test the Drive Speed – Stowed Position
- Q-15 Test the Drive Speed - Raised Position
- Annual Maintenance Procedures
- Programmed Maintenance Procedures
- P1-2 Inspect and Lubricate the Lifting Chains
- P2-2 Test or Replace the Hydraulic Oil
- Section 4 Repair Procedures
- Platform Controls
- Circuit Board
- Joystick
- Platform Emergency Stop Button
- Ground Controls
- Software Revision Level
- Machine Setup
- Level Sensors
- Hydraulic Pump
- How to Remove the Hydraulic Pump
- Function Manifold
- Valve Adjustments – Function Manifold
- Valve Coils
- Brake Release Hand Pump Components
- Hydraulic Tank
- Non-Steer Axle Components
- Steer Axle Components
- Steer Cylinder
- Steer Bellcrank
- Platform Components
- Platform Extension Deck
- Work Tray
- Mast Components
- How to Disassemble the Mast
- How to Assemble the Mast
- Glide Pads
- Lifting Chains
- How to Inspect the Lifting Chains
- Platform Overload Components
- Platform Overload Recovery Message
- Obstruction Sensing System
- Battery Charger
- Selecting a Charge Profile
- Batteries
- Diagnostics
- GCON I/O Map without Load Sense
- GCON I/O Map with Load Sense
- Diagnostic Trouble Codes (DTC)
- Troubleshooting "HXXX" and "PXXX" Faults
- Fault Inspection Procedure
- Type "HXXX" Faults
- Type "PXXX" Faults
- Type "UXXX" Faults
- Type "FXXX" Faults
- Type "CXXX" Faults
- Charger Fault Codes
- Charger Error Codes
- Section 6 Schematics
- Electrical Component and Wire Color Legends
- Wiring Diagram Ground and Platform Controls
- Electrical Symbol Legend
- Hydraulic Symbols Legend
- to GR16P
- from serial numbers GR16P-44174 to GR16P-46499 and QS16P-2469 to QS16P
- Electrical Schematic, QSR, AS/CE from serial number QS11-1000 to QS11-1015
- Hydraulic Schematics
Lift Guard GR-15
Table of contents
Related products
Lift Guard GR-12Lift Guard GR-20Lift Guard GRC-12Lift Guard GS-32Lift Guard GS-46Lift Guard GS-30Lift Guard GS-47Runabout GR-15Superlift SL-15Lift Tools GS-2669Genie categories
Garage Door Opener
Lifting Systems
Boom Lifts
Security Camera
Scissor Lifts
DVR
Digital Camera
Paper Shredder
Transmitter
Remote Control
manualsdatabase
Your AI-powered manual search engine