Barco Data 1209s Installation Manual

Also see for BarcoData 1209S: Owner's manual Owner's manual

Source connections7-2 5975718 BARCODATA 1209s 050698Connecting a S-Video (or Composite Video)source to Port 2Separate Y-luma/C-chroma signals for higher quality playback ofSuper VHS signals can be connected to Port 2 . A composite videosignal can also be connected to this port.To select the S-video input :Press the digit button 2 on the RCU or the local keypad.In case of using Port 2 for connecting the Composite Video, theselection of this source have to be done inside the "Picture Tuning"menu. Please refer to the Owner's Manual.75 W Termination Switch for S-videoTerminate the S-video input of the projector using the 75 Ω switch nextto the S-video input when the projector operates alone or when theprojector is the last unit in a loop-through configuration.The switch is set to "ON" : signal terminated.The switch is set to "OFF" : signal not terminated.Connecting a RGB Analog source to Port 3Connect a RGB Analog signal via an interface (e.g. RGB 120MHzinterface, part number 98 26570) to Port 3. RGB analog input withautomatic sync detection (Separate H and V sync inputs, withcomposite sync input or with sync signals on green) and automaticpolarity detection.Pin configuration of the D9 (male) connector of the Analog input :1 not connected2 ground RGBS3 RED4 GREEN5 BLUE6 ground RGBS7 ground RGBS8 Horizontal /composite sync9 Vertical syncTo select the RGB analog Input :Press the digit button 3 on the RCU or the local keypad.S1 Force Negative Sync(ON=yes)R81HsyncR101VsyncR41(Blue) R21(Green) R1(Red)S2 Blue in Green (ON=yes)Line termination 75 Ω resistorsLocations of the Termination Resistors and Switcheson the RGB Input Auto Sync Tracking ModuleWhen changing a switch position or removing a resistor, turn off theprojector and unplug the power cord from the wall outlet.75 W Termination resistorsIn case of chaining (loop-through) the projectors, the 75Ω linetermination resistors must be removed from the RGB Input Auto SyncTracking Module when the projector is NOT the last unit in the chain.In case of a stand-alone projector, do not remove the resistors.75 Ω resistors on the module : line terminated.75 Ω resistors removed : line not terminated.12344 pin connector configurations:For S-video:Pin 1: earth(ground) luminancePin 2: earth(ground) chrominancePin 3: luminance signal(Y)1Vpp ±3dBPin 4: chrominance signal(C)300mVpp ±3dBFor video:Pin 1: earth(ground) videoPin 2: not connectedPin 3: video signalPin 4: not connectedRKP2)) 2132579,'(232575*%+9&RPS+V\QF 9V\QF5 * %325732575(027(&20081,&$7,21352-(&72502'( 32:(50$,16325769,'(2RKP212))*5((1RSHUDWLRQDO5('VWDQGE\9&569+6$XGLRDPSOLILHU/XPD&KURPDWRQH[WSURMHFWRURUWRDPRQLWRU75 Ω TerminationSwitchRKP2)) 2132579,'(232575*%+9&RPS+V\QF 9V\QF5 * %325732575(027(&20081,&$7,21352-(&72502'(32:(50$,16325769,'(2RKP212))*5((1RSHUDWLRQDO5('VWDQGE\,13 ,135 *% + 9,1387$1$/2*,17(5)0+]212))LQYHURKPWHUP361RGB 120MHz interfaceAll manuals and user guides at all-guides.com