Barco Data 1209s Installation Manual

Also see for BarcoData 1209S: Owner's manual Owner's manual

Installation adjustment mode8-2 5975718 BARCODATA 1209s 050698Important : Access to adjustmentsThe top cover of the projector should be removed in order to gainaccess to the adjustments.Projector DistanceOn the screen, a drawing will be displayed together with parametersindicating a correct installation position.To change the screen width :1 Push the control disc to the left or to the right to highlight the itemSW in the "Projector Distance 1" menu and then press TEXT.If ENTER is pressed, the "Optical Lens Focusing" will be displayed.If EXIT is pressed, the projector will return to the previous menu.2 After TEXT is pressed, the next menu "Projector Distance 2" willbe displayed on the screen. It allows the user to change theScreen width.3 Push the control disc to the left or to the right to highlight the digitneeded to be changed, and enter the desired digit with the numerickeys on the RCU or the local keypad.4 Press ENTER to confirm the changes. The projector will re-displaythe "Projector Distance 1" menu with updated values for the threeparameters.5 Press ENTER to continue with the "Optical Lens Focusing".If EXIT is pressed, the projector will return to the previous menu.The same applies to the PD (projector distance). You can use theabove-mentioned procedure to obtain a correct updated value of SW(screenwidth) after entering a new value of PD (projector distance).Optical Lens FocusingThe optical focusing procedure is performed separately for eachlens. The appropriate CRT will be switched on as the user proceedsthrough the optical focusing adjustment sequence.Each lens has two focus adjustment points, one at the rear of the lensand one at the front. The center of the projected image is focused byloosening the wing nut at the rear end of the lens and rotating thelens barrel until the center of the image is clearly focused. The cornersof the projected image are focused by loosening the wing nut at thefront end of the lens and rotating the lens barrel until the corners ofthe image are clearly focused. Repetition of these adjustments maybe necessary to optimize optical focusing.Press ENTER to continue. After finishing focusing of the three lenses,press ENTER to enter the Raster centering.Press EXIT to return to operational mode.Press ADJUST key to return to operational mode.A = Correction valuePD= Perpendicular distance between screen and projectorSW= Screen widthSCREENWIDTH = 2 , 6 0 mSelect with arrow keys; reprogram with numeric keys andthen to confirm.Maximum screenwidth = 6 mMaximum proj. distance = 8,1 m.SW = 2.6 m PD= 3.64m A=12 cmSelect with arrow keys; to reprogram to continue; to return.WARNING: ONLY FOR STANDARD PROJECTORS !!OPTICAL LENS FOCUSING to continue to return1. LOOSEN THE NUT ON THEREAR OF THE XXXX LENS,ROTATE THE LENS BARRELTO FOCUS THE CENTEROF THE IMAGE,THEN TIGHTEN THE NUT2. LOOSEN THE NUT ON THEFRONT OF THE XXXX LENSAND ROTATE THE FRONTSECTION OF THE LENS TOFOCUS THE CORNERS OF THEIMAGE, THEN TIGHTEN THE NUT.150OPTICAL LENS FOCUSING to continue to return1. LOOSEN THE NUT ON THEREAR OF THE XXXX LENS,ROTATE THE LENS BARRELTO FOCUS THE CENTEROF THE IMAGE,THEN TIGHTEN THE NUT2. LOOSEN THE NUT ON THEFRONT OF THE XXXX LENSAND ROTATE THE FRONTSECTION OF THE LENS TOFOCUS THE CORNERS OF THEIMAGE, THEN TIGHTEN THE NUT.150OPTICAL LENS FOCUSING to continue to return1. LOOSEN THE NUT ON THEREAR OF THE XXXX LENS,ROTATE THE LENS BARRELTO FOCUS THE CENTEROF THE IMAGE,THEN TIGHTEN THE NUT2. LOOSEN THE NUT ON THEFRONT OF THE XXXX LENSAND ROTATE THE FRONTSECTION OF THE LENS TOFOCUS THE CORNERS OF THEIMAGE, THEN TIGHTEN THE NUT.Center focusingCorner focusing$3'VFUHHQSURMHFWRUFHLOLQJAll manuals and user guides at all-guides.com