DELTA DORE CS 8000 TYXAL+ User Manual

Also see for CS 8000 TYXAL+: Quick installation guide User guide

DELTA DORE CS 8000 TYXAL+ User Manual Manual pdf 16 page image

EN- 31 -- 30 -8.6 Button lightingÊ Enter the user code (e.g. 456789) and confirm with OK.Ë Press Settings, select the menu:Use > Products > Configure, then confirm with OK.Ì Select the touch screen keypad from the list of productsby clicking on "Browse", then confirm with OK.Í Select the "Button lighting" menu,then select "Activate" or "Deactivate" (Î).Confirm with OK.8.7 Button beepsÊ Enter the user code (e.g. 456789) and confirm with OK.Ë Press Settings, select the menu:Use > Products > Configure, then confirm with OK.Ì Select the touch screen keypad from the list of productsby clicking on "Browse", then confirm with OK.Í Select the "Button beeps" menu,then select "Activate" or "Deactivate" (Î).Confirm with OK.8.8 Screen brightnessÊ Enter the user code (e.g. 456789) and confirm with OK.Ë Press Settings, select the menu:Use > Products > Configure, then confirm with OK.Ì Select the touch screen keypad from the list of productsby clicking on "Browse", then confirm with OK.Í Select the "Brightness" menu,then set the value using the < and > arrows (Î).Confirm with OK.The Button lighting, Button beeps and Brightness buttonsettings only concern the touch screen keypad you use for thesesettings.4 5KeypadBrightnessOkBackButton beepsButton lighting< DeactivateOkBackButton lightingActivate >OkBackButton lighting4 5KeypadBrightnessOkBackButton beepsButton beeps< DeactivateOkBackButton beepsActivate >OkBackButton lighting4 5KeypadOkBackButton beepsButton lightingBrightnessOkBackBrightnessOkBackBrightness8. Personalising the products with your touch screen keypad8.9 Sound levelsÊ Enter the user code (e.g. 456789) and confirm with OK.Ë Press Settings, select the menu:Use > Products > Configure, then confirm with OK.Ì Select the product to change from the list of productsby clicking on "Browse", then confirm with OK.Í To set the sound level of the sirens, select the"Siren levels" menu, then select the type of signal toset (Î):- Intrusion, Technical, Fire, emergency alarm with siren ordoor chime(siren alarm control unit and indoor siren).- Intrusion, Pre-alarm, Fire, emergency alarm with siren(outdoor siren).Confirm with OK.Ï Set the sound level with the < and > buttons,then confirm with OK.Ð You can test the sound setting by confirming with Yes.The siren is briefly set off.Ñ To set the sound level of the problem andwarning beeps (except outdoor siren), select thebeep type, set the sound level, then confirm with OK.Ò You can test the sound setting by confirming with Yes.The control unit emits beeps briefly.UseZonesDoor chimeOkProductsBackConfigureBrowseBackPress the buttonof the productConfigureProductsOkActivate/deactivateBackSettingsClockLanguagesOkBackUseAccess codeXXXXXXOkSOSor BrowseConfigureOkBackCS 0 54 89SI 0 48 24123SEF 0 48 23489567Control unitTamper alarmBeep levelsExit timerConfirmation ON/OFFOkBackNameSiren levelsTechnicalFireSOS sonoreDoor chimeOkBackIntrusionBeep levelsWarning beepsOkBackProblem BeepsIntrusionOkBackProblem BeepsOkBackSiren levels25/11/14 12:48SOS SettingsOFFEnter your codeInfo SettingsMy houseOFF25/11/14 12:48Siren levelsIntrudertestYesNoBeep levelsProblem beepstestYesNoSetting the sound levels applies to the alarm control unit andthe outdoor and indoor sirens.Attention: resetting the intrusionsound level of a siren stops thesiren form sounding in the event of:- intrusion,- tamper alarm.OkBack