Denon AVR-1802 Operating Instructions Manual

Also see for AVR-1802: Operating instructions Brochure & specs Operating instructions Service manual Operating instructions

Contents

11Input the distances from the listening position to the speakers and set the surrounddelay time.Preparations:Measure the distances from the listening position to the speakers (L1 to L3 on thediagram at the right).L1: Distance from center speaker to listening positionL2: Distance from front speakers to listening positionL3: Distance from surround speaker to listening positionCAUTION:Set the center speaker at the same distance from the front speakers (left and right) or the subwoofer, or sothat the difference in distance (L2 – L 1) is 1.5 meters or less.Set the surround speakers (left and right) at the same distance from the front speakers (left and right) or thesubwoofer, or so that the difference in distance (L2 – L 3) is 4.5 meters or less.• The number changes in units of 0.1 meter each time one of the buttons ispressed. Select the value closest to the measured distance.(“/SW” appears only when subwoofer = yes.)Press the SELECT or (down) button to switch to the center speaker setting.L 1L 2L 36 FRNT/SW 3.6mListeningpositionCenterFL FRSetting the delay timeSL SRUse the (left) and (right) buttons to set the distance from the frontspeakers and subwoofer to the listening position.1Use the (left) and (right) buttons to set the distance from the centerspeakers to the listening position.2Use the (left) and (right) buttons to set the distance from the surroundspeakers to the listening position.3• The number changes in units of 0.1 meter each time one of the buttons ispressed. Select the value closest to the measured distance.Press the SELECT or (down) button to switch to the surround speaker setting.• The number changes in units of 0.1 meter each time one of the buttons ispressed. Select the value closest to the measured distance.Press the SELECT or (down) button to enter the setting and switch theDIGITAL input (COAX) setting.7 CENTER 3.6m8 SURR. 3.0mNOTE:• No setting when “None” has been selected for the center speaker.NOTE:• No setting when “None” has been selected for the surround speakers.NOTE:• The speaker distance can be adjusted between 0 and 18 meters in steps of 0.1 meter.ENGLISHNOTE:• PHONO, TUNER and V. AUX cannot be selected.• Select “OFF” if nothing is connected.Press the SELECT or (down) button to switch the OPTICAL input 2 (OPT 2)setting.9 COAX DVD CD DVD TV VCR1 VCR2 CDR OFF10 OPT1 TV CD DVD TV VCR1 VCR2 CDR OFFInput the type of components connected to the digital input terminals.Digital input setupUse the (left) and (right) buttons to set the type of device connectedto the COAXIAL input (COAXIAL) terminal.1Use the (left) and (right) buttons to set the type of device connectedto the OPTICAL input 1 (OPT 1) terminal.2(right) button(left) buttonPress the SELECT or (down) button to switch the optical input 1 (OPT 1)setting.(right) button(left) button• Select “OFF” if nothing is connected.This completes the system setup operations. Once the system is set up, there is no need to make the settingsagain unless other components or speakers are connected to or the speaker layout is changed.After setting up the systemPress the SYSTEM button to finish system set up.1(Initial)(Initial)• Select “OFF” if nothing is connected.11 OPT2 CDR CD DVD TV VCR1 VCR2 CDR OFFUse the (left) and (right) buttons to set the type of device connectedto the OPTICAL input 2 (OPT 2) terminal.3(right) button(left) buttonPress the SELECT or (down) button if you want to start the settings overfront the beginning.(Initial)