Denon AVR-1802 Operating Instructions Manual

Also see for AVR-1802: Operating instructions Brochure & specs Operating instructions Service manual Operating instructions

Contents

1211 REMOTE CONTROL UNITDENON remote-controllable audio components can be controlled using thisunit’s remote control unit. Note that some components, however, cannot beoperated with this remote control unit.Set the slide switch to the position for thecomponent to be operated (CD or MD/CDR). AUDIOCD MD/CDRVIDEOTITLEDISC SKIP+CD·MD/CDR·DVD/VDPVIDEO SELECTSYSTEM SURROUND98236 7TV/DBSVCR-1 VCR-2SURROUNDMODETUNER SHIFTV. AUX4859607INPUT MODE CDR / TAPECHANNELTAPE·VCR30026 7a. For CD player and MD/CD recorderb. For tape deck (TAPE)6,7 : Manual search(reverse and forward)2 : Stop1 : Play8,9 : Auto search3 : PauseDISC : Switch discsSKIP+ (for CD changers only)6 : Rewind7 : Fast-forward2 : Stop1 : Forward play0 : Reverse playBDVD/VDPCDPHONOTV/DBSVCR-1 VCR-2SURROUNDMODETUNER SHIFTREMOTE CONTROL UNIT RC-897STATUS MUTINGT.TONEMASTERVOLTITLEDISC SKIP+V. AUXINPUT MODE CDR / TAPECHANNEL TVCD·MD/CDR·DVD/VDPVIDE SELECTSYSTEMSET UP MENUSELECTRETURN DISPLAYSURROUNDCH SELECTVOLUMECHANNELAVR/AVC DVD/VDPTV VCRAUDIOCD MD/CDRVIDEOPOWERTAPE·VCROFF8495106273ON30026 798236 72-b2-a12-cTV/DBSVCR-1 VCR-2SURROUNDMODETUNER SHIFTV. AUXINPUT MODE CDR / TAPECHANNELTAPE·VCR30026 74859607c. For TUNERSHIFT : Switch preset channel rangeCHANNEL : Preset channel(+, –) (up/down)NOTE:• Tape deck (TAPE) and tuner can be operated when the switch is at “AUDIO” position.Operating DENON audio components1Use the buttons shown below to operate the audio component.For details, refer to the respective component’s manual.2DENON components can be operated by setting the preset memory for MD orCDR. Operation is not possible for some models.Set the slide switch to “MD/CDR”.AUDIOCD MD/CDRVIDEOBDVD/VDPCDPHONOTV/DBSVCR-1 VCR-2SURROUNDMODETUNER SHIFTREMOTE CONTROL UNIT RC-897STATUS MUTINGT.TONEMASTERVOLTITLEDISC SKIP+V. AUXINPUT MODE CDR / TAPECHANNEL TVCD·MD/CDR·DVD/VDPVIDEO SELECTSYSTEMSET UP MENUSELECTRETURN DISPLAYSURROUNDCH SELECTVOLUMECHANNELAVR/AVC DVD/VDPTV VCRAUDIOCD MD/CDRVIDEOPOWERTAPE·VCROFFON30026 798236 78495106273212Preset memory (Audio component)1Holding in the PLAY (1) button, press thebutton for the components you want to set.(Refer to table 1.)2BTable 1: Combinations of Personal SystemCodesMASTERVOL.MASTERVOL.PLAY (1) CD-RMDNOTE:• The memory can only be preset for either the MD or the CDR.Preset codes set upon shipment from the factory and whenreset.ENGLISHPreset memory (Video component)DENON and other makes of components can be operated by setting the preset memory for your make of videocomponent.This remote control unit can be used to operate components of other manufacturers without using the learningfunction by registering the manufacturer of the component as shown on the List of Preset Codes (page 171).Operation is not possible for some models.To continue registering other components, repeat steps 2 to 3.Bq wAUDIOCD MD/CDRVIDEOBq wBDVD/VDPCDPHONOTV/DBSVCR-1 VCR-2SURROUNDMODETUNER SHIFTREMOTE CONTROL UNIT RC-897STATUS MUTINGT.TONEMASTERVOLTITLEDISC SKIP+V. AUXINPUT MODE CDR / TAPECHANNEL TVCD·MD/CDR·DVD/VDPVIDEO SELECTSYSTEMSET UP MENUSELECTRETURN DISPLAYSURROUNDCH SELECTVOLUMECHANNELAVR/AVC DVD/VDPTV VCRAUDIOCD MD/CDRVIDEOPOWERTAPE·VCROFFON30026 798236 784951062731232. 3Set the slide switch to “VIDEO”.1Holding in the SHIFT button q, press the POWERbutton w of the components (DVD/VDP, VCR orTV) you want to set.Press and hold in the SHIFT button.2Holding in the SHIFT button q, press the numberbuttons w to input the preset code (consisting of2-digit numbers) for the manufacturer of thecomponent whose signals you want to store inthe memory.See the list on page 171 for the preset codes(consisting of 2-digit numbers).34NOTES:• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation,cover the remote control unit’s transmitting window while setting the preset memory.• Some models and years of manufacture of components of the manufacturers listed on the List of PresetCodes cannot be used.• The unit is equipped with several types of remote control codes which depend on the manufacturer. If thereis no operation, please change the preset code (a 2-digit number) and try again.