Denon AVR-2311 Owner's Manual

Also see for AVR-2311: Service manual Service manual Owner's manual

Contents

85ENGLISH Basic version Advanced versionSimple version InformationGHDMIHSymptom Cause/Solution PageNo audio isoutput with HDMIconnection.• Check the connection of the HDMI connectors.• When outputting HDMI audio from the speakers, set “HDMIAudio Out” on the menu to “AMP”.• When outputting HDMI audio from a TV, set “HDMI Audio Out”on the menu to “TV”.146161No video isoutput with HDMIconnection.• Check the connection of the HDMI connectors.• Set the input source to match the connected HDMI connector.• Check whether the TV is compatible with copyright protection(HDCP). If connected to a device not compatible with HDCP, videowill not be output correctly.1414, 2114When the followingoperations areperformed ondevices compatiblewith HDMI control,the same operationsoccur on this unit.• Power ON/OFF• Switching audiooutput devices• Adjust volume• Switch input source• Set “HDMI Control” on the menu to “OFF”. To operate poweronly for each device, set “Power Off Control” to “OFF”.39, 61GRadioHSymptom Cause/Solution PageReception fails, orthere is a lot of noiseor distortion.• Change the antenna orientation or position.• Separate the AM loop antenna from the unit.• Use an FM outdoor antenna.• Separate the antenna from other connection cables.19191919GiPodHSymptom Cause/Solution PageiPod cannot beplayed.• Check the iPod connections.• Plug the control dock for iPod’s AC adapter into a power outlet.• Switch the input source to “DOCK”.• If using an iPod connected to the USB port, incompatible iPodtypes cannot be played back.18–2124“Connection Error”is displayed.• Unable to communicate properly. Turn off the power to this unit,disconnect the iPod and then reconnect it.–“Not Support” isdisplayed.• The iPod connected to the unit is not compatible. Please makesure the iPod you are connecting is compatible.• The software version of the connected iPod is an old one. Pleaseupdate to the latest version.24–“Connection Error”is displayed.• The iPod is not responding. Turn off the power to this unit,disconnect the iPod and then reconnect it.–GUSB memory deviceHSymptom Cause/Solution PageWhen a USBmemory device isconnected, “USB” isnot displayed on themenu.• The set cannot recognize a USB memory device. Check theconnection.• A USB memory device not conforming to mass storage class isconnected. Connect a USB memory device conforming to massstorage class.• A USB memory device cannot be connected via a USB hub.18–18Files on a USBmemory devicecannot be played.• Set the USB memory device format to “FAT16” or “FAT32”. Fordetails, refer to the USB memory device’s operating instructions.• If the USB memory device is divided into multiple partitions, onlyfiles stored in the top partition can be played.• The file is recorded in an incompatible format. Please record it ina compatible format.• This unit cannot play back files covered by copyright protection.––––The file namesare not displayedproperly (“...”, etc.).• Characters that cannot be displayed on this unit are replaced by“.” (period).22, 24The sound quality ispoor or there is noiseduring playback.• The file being played back has a low bit rate. –“Connection Error”is displayed.• Unable to communicate properly. Turn off the power to this unit,unplug the USB memory device and then plug it back in.• The USB memory device is not responding. Turn off the power tothis unit, unplug the USB memory device and then plug it back in.––“Overcurrent” isdisplayed.• The USB memory device is consuming too much power. Whenusing a USB portable hard disk that can be powered by an ACadapter, connect its AC adapter.–GRemote control unitHSymptom Cause/Solution PageThe set cannot beoperated with theremote control unit.• Batteries are worn out. Replace with new batteries.• Operate the remote control unit within a distance of about 7 mfrom this unit and at an angle of within 30°.• Remove any obstacle between this unit and the remote controlunit.• Insert the batteries in the proper direction, checking the q andw marks.• The set’s remote control sensor is exposed to strong light (directsunlight, inverter type fluorescent bulb light, etc.). Move the setto a place in which the remote control sensor will not be exposedto strong light.7575757575