Denon AVR-4810CI Owner's Manual

Also see for AVR4810CI - 9.3 Channel Multi-Zone Home Theater Receiver: Specification Capabilites and Compatibilities Getting Started Connections Specifications Supplementary guide

Contents

Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsPlaybackAdjusting the Sound and Picture Quality (Audio/Video Adjust)Main remote control unitoperation buttons:Displaying the menuCancel the menu:Moves the cursor(Up/Down/Left/Right) :Confirm the setting :Return to previous menuSetting items Setting contentsToneAdjust the tonal quality ofthe sound.Tone Control : Sets the tone control function ON and OFF.ON : Allow tone adjustment (treble, bass).OFF : Playback without tone adjustment.This can be set when “Dynamic EQ” (vpage 92) is set to “OFF”.The tone cannot be adjusted in the direct mode.••••Bass : Adjust low frequency range (bass).–6dB ~ +6dBThis can be set when “Tone Control” is set to “ON”.•Treble : Adjust high frequency range (treble).–6dB ~ +6dBThis can be set when “Tone Control” is set to “ON”.•Audyssey SettingsSet MultEQ XT, Dynamic EQand Dynamic Volume.NOTEIf you have not performedAuto Setup, or if you changethe speaker settings afterperforming Auto Setup, youmay not be able to selectDynamic EQ/Dynamic Volume,and “Run Audyssey” may bedisplayed.In this case, either performAudyssey Auto Setup overagain or perform “Restore”(vpage 38) to return to thesettings after Audyssey AutoSetup was run.MultEQ XT : Corrects both time and frequency response problems in thelistening area.Audyssey : Optimize the frequency response of all speakers.Audyssey Byp.L/R : Optimize frequency response of speakers exceptfront L and R speakers.Audyssey Flat : Optimize frequency response of all speakers to flatresponse.Manual : Apply frequency response set with “Manual EQ” (vpage94).OFF : Turn “MultEQ XT” equalizer off.“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can beselected after Audyssey Auto Setup has been performed. “Audyssey”is automatically selected after performing Audyssey Auto Setup. “When“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected, “ ”lights.After running Audyssey Auto Setup, if the Speaker Configuration,Distance, Channel Level, and Crossover Frequency have changed withoutincreasing the number of speakers measured, only “ ” lights.If “Dynamic EQ” or “Dynamic Volume” is set to “ON” when “MultEQXT” is set to either “OFF” or “Manual”, “MultEQ XT” is automaticallyset to “Audyssey”.You can also press MULTEQ XT on the main remote control unit to set.NOTE“MultEQ XT” and “Manual” cannot be selected when “EQ Customize”is set to “Not Used” (vpage 45).When using headphones, “MultEQ XT” is set to “OFF”.•••••••••••Setting items Setting contentsAudyssey Settings(Continued)Dynamic EQ : Solves the problem of deteriorating sound quality asvolume is decreased by taking into account human perception and roomacoustics.ON : Use the Dynamic EQ equalizer.OFF : Do not use the Dynamic EQ equalizer.After performing “Audyssey Auto Setup”, the “Dynamic EQ” settingautomatically becomes “ON”.“ ” is displayed when set to “ON”.When “MultEQ XT” is set to “OFF” or “Manual”, “Dynamic EQ” isautomatically set to “OFF”.If “Dynamic Volume” is set to “ON”, “Dynamic EQ” is automaticallyset to “ON”.When you set ”Dynamic EQ” to ”ON”, “Tone Control” is switched”OFF”.You can also press DYNAMIC EQ on the main remote control unit toset.••••••••Dynamic EQ : ON/Volume : OFF“Green” “OFF”Dynamic EQ / Volume : OFFAbout Dynamic EQAudyssey Dynamic EQ™ solves the problem of deteriorating soundquality as volume is decreased by taking into account human perceptionand room acoustics. Audyssey Dynamic EQ works in tandem withAudyssey MultEQ® XT to provide well-balanced sound for every listenerat any volume level.“Red” “Off”See overleaf