Denon DVD-2910 Operating Instructions Manual

Also see for DVD-2910: Operating instructions Specifications Supplementary guide Operating instructions Service manual

17ENGLISHWhen “DIGITAL INTERFACE SETUP” is selectedSELECTHDMI/DVIOPEN/SUPER AUDIOFORMATNTSC/PAL CLOSECD SETUPPROGRAM/DIRECTCLEARCALLSEARCH MODEAUDIOSUBTITLEANGLEPAGEMARKERRANDOMDIMMERZOOMPICUREADJUSTSETUPMEMORYA-BREPEATSELECTRC-985PURE DIRECTDISPLAYTOP MENURETURNMENUSKIPSLOW/SEARCHPLAYSTILL/PAUSESTOPPOWER OFFPOWER ON11, 2, 312Use the • and ª cursor buttons to select the desired setting,then press the ENTER button.HDMI/DVI BLACK LEVELSwitches the digital RGB video level (data range) of theHDMI and the DVI-D terminals.HDMI AUDIO SETUPUse this to adjust for the audio signals from the HDMIterminal.E X I T SE TUPNORMAL2CHD I G I TA L I NTERF ACE SETUPHDMI/ DV I BLACK LEVELHDM I AUDIO SETUPDEC I S I ON : ENTER BUT TONSE L ECT :1 See page 14.Remote control unit Remote control unit3Use the • and ª cursor buttons to select the desired setting,then press the ENTER button.q When “HDMI/DVI BLACK LEVEL” is selected:NORMAL (Factory default)Signals are output from the HDMI and the DVI-D terminalswith a digital RGB video level (data range) of 16(black) to235(white).ENHANCEDSignals are output from the HDMI and the DVI-D terminalswith a digital RGB video level (data range) of 0(black) to246(white).✽ When the HDMI and the DVI-D terminals areconnected, the black may seem to stand out, dependingon the TV or the Monitor you are using. In this case, setthis to “ENHANCED”.✽ When select “HDMI Y Cb Cr” under “HDMI/DVISELECT”, will have no effect. (See page 26.)DEC I S I ON : ENTER BUT TONSE L ECT :D I G I TA L I NTERF ACE SETUPE X I T SE TUPHDMI/ DV I BLACK L EVELHDM I AUDIO SETUPNORMALENHANCEDDEC I S I ON : ENTER BUT TONSE L ECT :D I G I TA L I NTERF ACE SETUPE X I T SE TUPHDMI/ DV I BLACK L EVEL2CHMULTI(NORMAL)MULTI(LPCM)HDM I AUDIO SETUPHDMI SPEAKER SE TUPSPEAKER CONF I GURAT I ONCHANNE L L EVE LDE L AY T I M EDIGITAL INTERFACE SETUPDEC I S I ON : ENTER BUT TONSE L ECT :3w When “HDMI AUDIO SETUP” is selected:2CH (channel) (Factory default)The audio signals are output from the HDMI terminal witha down-mixed to 2 channel.MULTI(NORMAL)The multi-channel audio signals are output from the HDMIterminal with a bit-stream.MULTI(LPCM)The multi-channel audio signals are output from the HDMIterminal with a linear PCM.B When “MULTI (LPCM)” is selected, use the • and ªcursor buttons to select the item to be set, then pressthe ENTER button.SPEAKER CONFIGURATIONUse this to select the types of the different speakers.CHANNEL LEVELUse this to adjust the output level of the differentspeakers.DELAY TIMEUse this to set the distance from the differentspeakers to the listening position.✽ To exit the HDMI SPEAKER SETUP modeUse the ª cursor button to select “DIGITALINTERFACE SETUP” then press ENTER button.B When “SPEAKER CONFIGURATION” is selected, usethe • and ª cursor buttons to select the speaker to beset then press the ENTER button.• The type of speaker used for the front speakers,center speaker, subwoofer and surround speakerscan be set. Use the • and ª cursor buttons toselect the speaker type, then press the ENTERbutton.LARGESelect this when a large speaker is connected.SMALLSelect this when a small speaker is connected.NONESelect this when no speaker is connected.YESSelect this when a subwoofer is connected.NOSelect this when no subwoofer is connected.✽ Press the RETURN button to return to the “HDMISPEAKER SETUP” menu.B When “CHANNEL LEVEL” is selected, use the • andª cursor buttons to select the speaker to be adjusted,then use the 0 and 1 cursor buttons to set the level.TEST TONE• Use the 0 and 1 cursor buttons to select auto ormanual.Adjust so that the volume of the test tones outputfrom the different speakers sounds the same.• The volume level output from the front speakers(left and right channels), center speaker, surroundspeakers (left and right channels) and subwoofer canbe adjusted.• The volume level can be adjusted between 0 and -10dB in steps of 1 dB.✽ Press the RETURN button to return to the “HDMISPEAKER SETUP” menu.HDMI SPEAKER SE TUPSPEAKER CONF I GURAT I ONF RONT SPCENT ER SPSUBWOOF ERSURROUND SPL ARGEL ARGEYESL ARGEDEC I S I ON : ENTER BUT TONSE L ECT :Remote control unit Remote control unitHDMI SPEAKER SE TUPCHANNEL LEVELDEC I S I ON : ENTER BUT TONSE L ECT :TEST TONEF RONT L CHCENT ERF RONT RCHSURROUND RCHSURROUND L CHSUBWOOF EROF F0 dB0 dB0 dB0 dB0 dB0 dBThe display depends on theconnected device. (Indicateswhether or not speakers areconnected)