Denon DVD-2910 Operating Instructions Manual

Also see for DVD-2910: Operating instructions Specifications Supplementary guide Operating instructions Service manual

26ENGLISHSTD(STANDARD)M1(MEMORY1)M2(MEMORY2)M3(MEMORY3)M4(MEMORY4)M5(MEMORY5)SET(PIC SETUP)1(ADJUSTMENT 1)2(ADJUSTMENT 2)GAMMACONTRASTBRIGHTNESSSHARPNESS(MID)SHARPNESS(HI)HUECCSWHITE LEVELCHROMA LEVELCHROMA DELAYDNRG0~G9SETUP LEVELH.POSITIONV.POSITIONPICTURE MODE✽1 Only effective for progressive scan.✽2 Only effective for HDMI, DVI andprogressive scan.• When HDMI and DVI signals areoutput, the SHARPNESS (MID/HI),CHROMA DELAY and Gammacorrection settings will have noeffect.✽16When the Display Position is Selected andAdjusted:• Press the cursor button (ª), then select thehorizontal/vertical direction with the cursorbuttons (0, 1), set the adjustment value withthe (• , ª ) cursor buttons, and press theENTER button.SETUP LEVEL (0 IRE, 7.5 IRE)(Factory default: 0 IRE)• This corrects floating black.H. POSITION (–7 to +7) (Factory default: 0)• A 15-step portion of position adjustment ispermitted left and right.V. POSITION (–3 to +7) (Factory default: 0)• A 11-step portion of position adjustment ispermitted up and down.✽ The picture and sound may be disturbed whilethe display position is being adjusted.✽ To exit the picture adjust modePress the PICTURE ADJUST button.P I CTURE MODESTD M1 M2 M3 M4 M5 SETP I C SETUPSETUP LEVE L 0 00Remote control unitRemote control unit✽2✽1✽2✽212 USING THE VIDEO SETUP2 The video output setting of the HDMI and the DVI-D connectors can be changed.2 The video output setting of the PICTURE MODE, PROGRESSIVE MODE and ADJUST MODE also can bechanged.DBYDVD-2910DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYERSTILL / PAUSEPLAY STOPOPEN/CLOSEAUDIO CDSETUPHDMI / DVISELECT FORMATSELECTDIRECTPURESUPER21✽ The HDMI, DVI, 480P, 576P, 720P and 1080iindicators flash when the connection is beingchecked, then stop flashing, remaining lit, oncethe check is completed.1Press the HDMI/DVI SELECT button.• The modes described below will appear on thedisplay.HDMI/DVI OFF (FACTORY DEFAULT)No output signals from the HDMI and DVI-Dconnectors.This mode is set to use the COMPONENT VIDEOOUT connector.HDMI Y Cb CrOutputs the component signals from the HDMIconnector.HDMI RGBOutputs the RGB signals from the HDMIconnector.DVIOutputs the RGB signals from the DVI-Dconnector.✽ The video signals are only output from one ofthe HDMI, DVI or progressive componentvideo output connectors.SELECT FORMATHDMI / DVIMain unitDVIHDMI Y Cb CrHDMI R G B2Press the HDMI/DVI FORMAT button.• The modes described below will appear on thedisplay.Select the item you wish to set and press theselect knob to define it.480P/576P (FACTORY DEFAULT)Outputs the image from the HDMI or DVI-Dconnector at 480P or 576P.720POutputs the image from the HDMI or DVI-Dconnector at 720P.1080iOutputs the image from the HDMI or DVI-Dconnector at 1080i.• When playing back a PAL-formated disc, be sureto set the TV TYPE option to NTSC. (See pages 18,19.)• The video or audio signals may be interruptedwhen the output setting mode is switched.• Depending on the TV you are using, if the TV’sinput is not set to HDMI or DVI, the HDMI or DVIOFF mode may be set. In this case, set the TV’sinput setting to HDMI or DVI before performingthe DVI setup procedure.• Connect to an HDCP compatible display to viewimages with DVI connections.480P/576P720P1080iSELECT FORMATHDMI / DVIMain unitSELECTHDMI/DVIOPEN/SUPER AUDIOFORMATNTSC/PAL CLOSECD SETUPPROGRAM/DIRECTCLEARCALLSEARCH MODEAUDIOSUBTITLEANGLEPAGEDIMZOOMA-BURDISPLAYTOP MENURETURNMENUSKIPSLOW/SEARCHPLAYSTILL/PAUSESTOPPOWER OFFPOWER ON1 2HDMI/DVI OFFSELECTHDMI/DVIFORMATRemotecontrol unitSELECTHDMI/DVIFORMATRemote control unitDisplay the setting mode