Denon DVD-3910 Operating Instructions Manual

Also see for DVD-3910: Supplementary guide Specifications Specification Operating instructions Service manual

33ENGLISH3w When “HDMI AUDIO SETUP” is selected:2CH (Channel) (Factory default)The audio signals are output from the HDMI terminal with a down-mixed to 2 channel.MULTI(NORMAL)The multi-channel audio signals are output from the HDMI terminalwith a bit-stream.MULTI(LPCM)The multi-channel audio signals are output from the HDMI terminalwith a linear PCM.B When “MULTI (LPCM)” is selected, use the • and ª cursorbuttons to select the item to be set, then press the ENTERbutton.SPEAKER CONFIGURATIONUse this to select the types of the different speakers.CHANNEL LEVELUse this to adjust the output level of the different speakers.DELAY TIMEUse this to set the distance from the different speakers to thelistening position.✽ To exit the SPEAKER SETUP mode.Use the ª cursor button to select “DIGITAL INTERFACE SETUP”then press ENTER button.B When “SPEAKER CONFIGURATION” is selected, use the • andª cursor buttons to select the speaker to be set then press theENTER button.• The type of speaker used for the front speakers, center speaker,subwoofer and surround speakers can be set. Use the • and ª cursorbuttons to select the speaker type, then press the ENTER button.LARGESelect this when a large speaker is connected.SMALLSelect this when a small speaker is connected.NONESelect this when no speaker is connected.YESSelect this when a subwoofer is connected.NOSelect this when no subwoofer is connected.• When “CROSSOVER” is selected:40 Hz, 60 Hz, 80 Hz (Factory default), 100 Hz, 120 Hz, set thefrequency of cross over.✽ Press the RETURN button to return to the “HDMI SPEAKERSETUP” menu.B When “CHANNEL LEVEL” is selected, use the • and ª cursorbuttons to select the speaker to be adjusted, then use the 0 and1 cursor buttons to set the level.TEST TONE• Use the 0 and 1 cursor buttons to select auto or manual.Adjust so that the volume of the test tones output from the differentspeakers sounds the same.• The volume level output from the front speakers (left and rightchannels), center speaker, surround speakers (left and rightchannels) and subwoofer can be adjusted.• The volume level can be adjusted between 0 and -10 dB in steps of1 dB.✽ Press the RETURN button to return to the “HDMI SPEAKERSETUP” menu.DEC I S I ON : ENTER BUT TONSE L ECT :D I G I TA L I NTERF ACE SETUPE X I T SE TUPHDMI/ DV I BLACK L EVEL2CHMULTI(NORMAL)MULTI(LPCM)HDM I AUDIO SETUPDENON LINKIEEE1394HDMI SPEAKER SE TUPSPEAKER CONF I GURAT I ONCHANNE L L EVE LDE L AY T I MEDIGITAL INTERFACE SETUPDEC I S I ON : ENTER BUT TONSE L ECT :HDMI SPEAKER SE TUPSPEAKER CONF I GURAT I ONF RONT SPCENT ER SPSUBWOOF ERSURROUND SPCROSSOVE RL ARGEL ARGEYESL ARGE80HzDEC I S I ON : ENTER BUT TONSE L ECT :HDMI SPEAKER SE TUPCHANNEL LEVELDEC I S I ON : ENTER BUT TONSE L ECT :TEST TONEF RONT L CHCENT ERF RONT RCHSURROUND RCHSURROUND LCHSUBWOOF EROF F0 dB0 dB0 dB0 dB0 dB0 dBRemote control unit Remote control unitThe display depends on the connected device.(Indicates whether or not speakers areconnected)