Dynex DX-22LD150A11 User Manual

Also see for DX-19LD150A11: Important information Quick setup guide User guide Guía De Instalación Rápida Guía del usuario

Contents

12 Understanding the basicsDX-19LD150A11/DX-22LD150A11If you chose Home mode (default - has the same settings as theEnergy Saving picture mode), the Choose your TV source screenopens. If you chose Retail mode (has the same settings as theVivid picture mode), you will be asked whether you really wantthis mode, because no energy savings will be realized with yourTV/DVD combo in this mode.If you select No, press ENTER. The Choose your TV Picture Modescreen reopens. Go back to Step 5.- OR -If you select Yes, press ENTER. The Choose your TV source screenopens.6 Press or to select Antenna, Cable, or Cable/SatelliteBox, depending on the type of connection you have, then pressENTER.• If you are using an antenna for a standard or HD TV signal,select Antenna.• If your cable is connected directly to the TV/DVD combo(without a tuner box), select Cable.• If your cable is connected to your TV/DVD combo through atuner box, select Cable/Satellite Box.If you selected Antenna or Cable, your TV/DVD comboautomatically scans for available channels in your area and storesthe channel information in the channel list. This may take severalminutes. While scanning, the TV/DVD combo displays a progressreport.– OR –If you selected Cable/Satellite Box, the auto scan is notnecessary and will not appear.Note: During auto scan, digital programs will be scanned first, thenanalog programs. When all available digital programs have beensearched, the screen will ask you to “Press EXIT if you don’t needanalog channel scan.” At this point you can press EXIT to exit theanalog channel scan, or just ignore it and the TV/DVD combo will goon scanning.You can press EXIT at any time to stop the auto scan, but you will need torun the auto scan again to create a channel list.7 Select the corresponding video input source through the INPUTSOURCE menu.Note: You can change the menu language or scan for channels at a laterdate. For more information, see “Selecting the menu language andtransparency” on page 26 or “Automatically searching for TVchannels” on page 17.Understanding the basicsTurning your TV/DVD combo on or offTo turn your TV/DVD combo on or off (standby mode):1 Plug the power cord into an AC power outlet.2 Press (power). Your TV/DVD combo turns on.3 Press again to turn off your TV/DVD combo. When you turn offyour TV/DVD combo, it goes into standby mode.Warning: When your TV/DVD combo is in standby mode, it is stillreceiving power. To completely disconnect power, unplug the powercord.Note: If your TV/DVD combo is connected to a computer and the TV/DVDcombo receives no VGA signal, the TV/DVD combo will enter DPMS(Display Power Management System) mode automatically. You canpress (Power) to wake up your TV/DVD combo.Selecting the video input sourceTo select the video input source:1 Turn on your TV/DVD combo, then press the INPUT key on theremote, or the INPUT button on the side of your TV/DVD combo.The INPUT SOURCE menu opens.2 Press INPUT repeatedly or press or to highlight the videosource, then press ENTER.Selecting a channelTo select a channel:• Press CH or CH to go to the next or previous channel on thememorized channel list.• Press the number buttons to enter the analog or digital (main)channel number you want, then wait for the channel to change,or press ENTER to change the channel immediately.• To select a digital sub-channel, press the number buttons toselect the main digital channel, then press the dash (–)button to select the sub-channel. Wait for the channel tochange, or press ENTER to change the channel immediately.Note: Button presses must be within three seconds of each other.• Press RECALL to go to the last channel viewed. Press RECALLagain to return to the channel you were watching.Adjusting the volumeTo adjust the volume:• Press VOL+ or VOL– to increase or decrease the volume.• Press MUTE to temporarily turn off all sound. Press MUTEagain to restore the sound.